CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Modifying an X-Y table - ACME - EPOXY

Posted by ccq@x...
on 2003-09-03 10:10:15 UTC
On Wed Sep 3 06:57:37 2003 turbulatordude wrote:

>--- In CAD_CAM_EDM_DRO@yahoogroups.com, JanRwl@A... wrote:
>> In a message dated 9/2/2003 10:39:47 PM Central Standard Time,
>> davemucha@j... writes:
>>
>> > Since ACME is not a taper, jsut squeezing the nut does not
>> > automatically mean a tighter fit...
>> >
>>
>> GOOD point, and why I like "stub-ACME" which DOES have the
>slightest taper,
>> so "squeezing" the nut very carefully DOES work! (This trick works
>best with
>> Turcite nuts, with home-brew addition of "squeeze mechanism or
>screw, etc.!)
>>
>> Jan Rowland
>
>I just realized that since the taped hole in the vice would not
>benefit from teh slice and clamp along the axis of the thread, it
>could work on a line perpendicular to the axis.

That's the usual way to do this trick with a brass nut. The part after that
goes: Take a _tapered_ screw, and grind the end off until only one turn will
fit into the tapped hole, and tighten it in until the backlash goes away. The
problem is that this can loosten up frequently, requireing frequent re-
adjustment.

It seems to me, that making a pair of nuts with a large tab sticking out to the
side on each of them would be a better way to go. Drill a hole parallel to the
axis in each tab, for a small bolt. Tightening the bolt, and lock nutting it
in place, would be a much more stable way of making this trick work.

Bill

>One would still slice the casting somewhere so that the cut is about
>1/2 to 3/4 thru the nut section, then, another cut on one of the
>connecting legs. This would have the effect of the nuts, one after
>the other, connected where there was no saw cut, and one of those
>being split.
>
>Threading the two towgether with a single bolt would allow one to
>twist to create tention. or to remove the backlash. The BIG risk is
>breaking the casting.... been there, done that !
>
>On my HF vice, the taped hole is really sloppy !
>
>A word of caution and a question.
>
>Using some home brew epoxy to create nuts has the risk of really
>locking up the screw.
>
>Any ideas what is used or can be used as a home-brew release agent ?
>
>Dave
>
>
>
>
>Addresses:
>FAQ: http://www.ktmarketing.com/faq.html
>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
>Moderator: pentam@... indigo_red@... [Moderators]
>URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
>OFF Topic POSTS: General Machining
>If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
>http://www.metalworking.com/news_servers.html
>
>http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
>
>NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
>bill
>List Mom
>List Owner
>
>
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>

--
----------------------------------------------------------------------------
RKBA! ***** Blessings On Thee, Oh Israel! ***** 4-19!
----------------+----------+--------------------------+---------------------
An _EFFECTIVE_ | Insured | All matter is vibration. | Let he who hath no
weapon in every | by COLT; | -- Max Planck | weapon sell his
hand = Freedom | DIAL | In the beginning was the | garment and buy a
on every side! | 1911-A1. | word. -- The Bible | sword.--Jesus Christ
----------------+----------+--------------------------+---------------------

Constitutional Government is dead; LONG LIVE THE CONSTITUTION!!!!!

----------------------------------------------------------------------------

Discussion Thread

Chuck Knight 2003-08-31 00:31:52 UTC Modifying an X-Y table Peter L. Peres 2003-08-31 14:20:34 UTC Re: [CAD_CAM_EDM_DRO] Modifying an X-Y table Chuck Knight 2003-08-31 19:26:13 UTC Re: [CAD_CAM_EDM_DRO] Modifying an X-Y table Jeff Demand 2003-08-31 19:53:42 UTC Re: Modifying an X-Y table sam sokolik 2003-08-31 20:10:22 UTC Re: [CAD_CAM_EDM_DRO] Modifying an X-Y table ccq@x... 2003-08-31 21:48:16 UTC Re: [CAD_CAM_EDM_DRO] Modifying an X-Y table Chuck Knight 2003-08-31 21:54:42 UTC Re: [CAD_CAM_EDM_DRO] Re: Modifying an X-Y table sam sokolik 2003-08-31 22:27:26 UTC Re: [CAD_CAM_EDM_DRO] Modifying an X-Y table grantfair2001 2003-08-31 23:34:50 UTC Re: Modifying an X-Y table Robb Greathouse 2003-09-01 13:32:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Modifying an X-Y table ballendo 2003-09-02 04:50:02 UTC Re: Modifying an X-Y table turbulatordude 2003-09-02 07:50:34 UTC Re: Modifying an X-Y table - ACME Chuck Knight 2003-09-02 19:16:19 UTC Re: [CAD_CAM_EDM_DRO] Re: Modifying an X-Y table - ACME turbulatordude 2003-09-02 20:37:48 UTC Re: Modifying an X-Y table - ACME - for fun and learning JanRwl@A... 2003-09-02 20:43:38 UTC Re: [CAD_CAM_EDM_DRO] Re: Modifying an X-Y table - ACME - for fun and learning m0nkey0ne 2003-09-03 01:26:21 UTC Re: Modifying an X-Y table - ACME - for fun and learning turbulatordude 2003-09-03 06:57:50 UTC Re: Modifying an X-Y table - ACME - EPOXY Peter L. Peres 2003-09-03 07:39:15 UTC Re: [CAD_CAM_EDM_DRO] Re: Modifying an X-Y table ccq@x... 2003-09-03 10:10:15 UTC Re: [CAD_CAM_EDM_DRO] Re: Modifying an X-Y table - ACME - EPOXY Chris Baugher 2003-09-03 11:27:07 UTC Re: [CAD_CAM_EDM_DRO] Re: Modifying an X-Y table - ACME - EPOXY Chuck Knight 2003-09-03 16:28:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Modifying an X-Y table - ACME - EPOXY ballendo 2003-09-04 03:56:10 UTC Re: Modifying an X-Y table - ACME - for fun and learning ballendo 2003-09-04 04:01:45 UTC Re: Modifying an X-Y table turbulatordude 2003-09-04 06:11:52 UTC Re: Modifying an X-Y table - ACME - for fun and learning Chuck Knight 2003-09-04 10:14:42 UTC Re: [CAD_CAM_EDM_DRO] Re: Modifying an X-Y table - ACME - for fun and learning sam sokolik 2003-09-04 10:36:39 UTC Re: [CAD_CAM_EDM_DRO] Re: Modifying an X-Y table - ACME - for fun and learning turbulatordude 2003-09-04 16:17:44 UTC Re: Modifying an X-Y table - ACME - for fun and learning Tim Goldstein 2003-09-04 16:36:03 UTC RE: [CAD_CAM_EDM_DRO] Re: Modifying an X-Y table - ACME - for fun and learning JanRwl@A... 2003-09-04 20:57:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Modifying an X-Y table - ACME - for fun and learning Chuck Knight 2003-09-04 22:50:27 UTC Re: [CAD_CAM_EDM_DRO] Re: Modifying an X-Y table - ACME - for fun and learning JanRwl@A... 2003-09-05 13:11:16 UTC Re: [CAD_CAM_EDM_DRO] Re: Modifying an X-Y table - ACME - for fun and learning