Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed -
Posted by
Weyland
on 2003-09-13 19:33:57 UTC
Thanks for the tip, Jeff.
I'll look into that Monoday.
Best,
Weyland
On Friday 12 September 2003 11:59 pm, washcomp spake:
I'll look into that Monoday.
Best,
Weyland
On Friday 12 September 2003 11:59 pm, washcomp spake:
> Weyland:
>
> If you're more interested in combating voltage fluctuations than
> running your mill during a blackout, you might want to look at a
> voltage regulator rather than a UPS. They generally keeps the
> voltage at about 120, over a pretty broad voltage range (87v-140v
> for the one I checked):
>
> http://www.tripplite.com/products/conditioners/index.cfm
>
> 15 amp = about 1380 watts or about 1500 volt-amperes
>
> A unit this size will cost significantly less than a UPS and should
> adress what you're looking for. I'd call Tripplite on Monday and
> speak to an engineer as a sanity check because of the inductive
> nature of the load and the motor surges and ask for their guidance.
Discussion Thread
Weyland
2003-09-12 18:15:35 UTC
Clarifications needed -
Tim Goldstein
2003-09-12 18:34:54 UTC
RE: [CAD_CAM_EDM_DRO] Clarifications needed -
washcomp
2003-09-12 18:45:04 UTC
Re: Clarifications needed -
Weyland
2003-09-12 19:45:08 UTC
Re: [CAD_CAM_EDM_DRO] Clarifications needed -
Tim Goldstein
2003-09-12 19:55:48 UTC
RE: [CAD_CAM_EDM_DRO] Clarifications needed -
Weyland
2003-09-12 19:56:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed -
Weyland
2003-09-12 20:09:51 UTC
Re: [CAD_CAM_EDM_DRO] Clarifications needed -
Tim Goldstein
2003-09-12 20:40:20 UTC
RE: [CAD_CAM_EDM_DRO] Re: Clarifications needed -
Jon Elson
2003-09-12 20:42:47 UTC
Re: [CAD_CAM_EDM_DRO] Clarifications needed -
washcomp
2003-09-12 20:59:18 UTC
Re: Clarifications needed -
Jon Elson
2003-09-12 21:16:10 UTC
Re: [CAD_CAM_EDM_DRO] Clarifications needed -
Jon Elson
2003-09-12 21:27:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed -
Harvey White
2003-09-12 21:48:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed -
turbulatordude
2003-09-13 06:12:48 UTC
Re: Clarifications needed - 5 volts
Graham Stabler
2003-09-13 09:01:17 UTC
Re: Clarifications needed - 5 volts
Harvey White
2003-09-13 09:37:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - 5 volts
Keith Bowers
2003-09-13 12:48:21 UTC
Re: [CAD_CAM_EDM_DRO] Clarifications needed -
Alan Marconett KM6VV
2003-09-13 13:09:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - 5 volts
Mariss Freimanis
2003-09-13 14:21:11 UTC
Re: Clarifications needed - 5 volts
Harvey White
2003-09-13 14:29:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - 5 volts
Weyland
2003-09-13 19:04:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed -
Weyland
2003-09-13 19:32:30 UTC
Re: [CAD_CAM_EDM_DRO] Clarifications needed -
Weyland
2003-09-13 19:33:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed -
Weyland
2003-09-13 19:40:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed -
Weyland
2003-09-13 19:46:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - 5 volts
Tim Goldstein
2003-09-13 21:16:52 UTC
RE: [CAD_CAM_EDM_DRO] Re: Clarifications needed -
Weyland
2003-09-13 21:36:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed -
Antonius J.M. Groothuizen
2003-09-13 22:24:37 UTC
Re: Clarifications needed -
amoss_70
2003-09-13 23:37:20 UTC
Re: Clarifications needed -
Graham Stabler
2003-09-14 12:13:24 UTC
Re: Clarifications needed - 5 volts