CAD CAM EDM DRO - Yahoo Group Archive

Re: Clarifications needed -

Posted by amoss_70
on 2003-09-13 23:37:20 UTC
Here's how I do it.

Take the +5 from a connector inbside the PC and run it to the
gecko's. don't connect the ground, as the signals lines will act as
the ground.

The high voltage WILL cook your servo's, set your timer to three
minutes and watch them cook. (of course you could have some
seriously high voltage servos, which would love that voltage, but the
gecko's will cook). You should have some serious heat sinks behind
them as well.

Just remember the Keep It Simple thing. loose the power supply. get
some 1440 VA ups off of ebay. open UPS case and use the 24v across
those 2 big batteries. They will be fused for somthing in the 100A
area so you'll be good to go. Plug the PC power in the back of the
UPS. Turn off the UPS warning beeper, as when you do a rapid
traverse the UPS "see's" that as a bad battery and will start
screaming.

I run my setup from 9am to 10pm (yes 13 hours a day) and nothing gets
hot to the touch. Warm yes, but never, ever warmer than my coffee
mug :) I will snap 3/8 cutters all day before I tax the servos.

If you want to email me Aaron_Moss@... well do the phone
number thing and walk through the rest of the steps or BS to check.


thanks




--- In CAD_CAM_EDM_DRO@yahoogroups.com, Weyland <weyland@v...> wrote:
> Hi All~!
>
> Trying to finish up my conversion tonight or
> tomorrow, but need some things clarified before I can.
>
> First - Geckos and voltage.
> My power supply is putting out 82.6 VDC.
> And I've wired the Geckos in the "star" configuration recommended.
> My concern is over the 80 VDC limit for the Geckos.
> (G210s marked with "90IFX" on the covers.)
>
> Second, I'm confused about the capacitors one
> might or might not use on the Geckos themselves.
> My power supply is pretty close to the
> Geckos, but the motor cables run 10 feet long.
> Do I need capacitors? Which size?
>
> Third - the +5V.
> Assuming that I want to work with what I have right now and not
need to
> spend more money, do I get that +5V from the computer power supply
> or does it come from somewhere in the parallel port?
>
> And Fourth, I'm planning on using a UPS for the controller, and
wanted
> to know people's thoughts on using it for the motor's power supply
as well.
>
> Thanks,
>
> Weyland

Discussion Thread

Weyland 2003-09-12 18:15:35 UTC Clarifications needed - Tim Goldstein 2003-09-12 18:34:54 UTC RE: [CAD_CAM_EDM_DRO] Clarifications needed - washcomp 2003-09-12 18:45:04 UTC Re: Clarifications needed - Weyland 2003-09-12 19:45:08 UTC Re: [CAD_CAM_EDM_DRO] Clarifications needed - Tim Goldstein 2003-09-12 19:55:48 UTC RE: [CAD_CAM_EDM_DRO] Clarifications needed - Weyland 2003-09-12 19:56:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - Weyland 2003-09-12 20:09:51 UTC Re: [CAD_CAM_EDM_DRO] Clarifications needed - Tim Goldstein 2003-09-12 20:40:20 UTC RE: [CAD_CAM_EDM_DRO] Re: Clarifications needed - Jon Elson 2003-09-12 20:42:47 UTC Re: [CAD_CAM_EDM_DRO] Clarifications needed - washcomp 2003-09-12 20:59:18 UTC Re: Clarifications needed - Jon Elson 2003-09-12 21:16:10 UTC Re: [CAD_CAM_EDM_DRO] Clarifications needed - Jon Elson 2003-09-12 21:27:04 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - Harvey White 2003-09-12 21:48:41 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - turbulatordude 2003-09-13 06:12:48 UTC Re: Clarifications needed - 5 volts Graham Stabler 2003-09-13 09:01:17 UTC Re: Clarifications needed - 5 volts Harvey White 2003-09-13 09:37:11 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - 5 volts Keith Bowers 2003-09-13 12:48:21 UTC Re: [CAD_CAM_EDM_DRO] Clarifications needed - Alan Marconett KM6VV 2003-09-13 13:09:37 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - 5 volts Mariss Freimanis 2003-09-13 14:21:11 UTC Re: Clarifications needed - 5 volts Harvey White 2003-09-13 14:29:22 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - 5 volts Weyland 2003-09-13 19:04:38 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - Weyland 2003-09-13 19:32:30 UTC Re: [CAD_CAM_EDM_DRO] Clarifications needed - Weyland 2003-09-13 19:33:57 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - Weyland 2003-09-13 19:40:28 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - Weyland 2003-09-13 19:46:04 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - 5 volts Tim Goldstein 2003-09-13 21:16:52 UTC RE: [CAD_CAM_EDM_DRO] Re: Clarifications needed - Weyland 2003-09-13 21:36:32 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - Antonius J.M. Groothuizen 2003-09-13 22:24:37 UTC Re: Clarifications needed - amoss_70 2003-09-13 23:37:20 UTC Re: Clarifications needed - Graham Stabler 2003-09-14 12:13:24 UTC Re: Clarifications needed - 5 volts