CAD CAM EDM DRO - Yahoo Group Archive

Re: Clarifications needed -

on 2003-09-13 22:24:37 UTC
> I'm not sure at this point if it makes a difference, but all
> three motors ( with a fourth later) run off of this voltage.
> I'm guessing, but it seems possible to have all three axis' drawing
> off of the output voltage at once, making each get 1/3 available...
> Or am I thinking of this incorrectly?
>
> Weyland

The voltage will be the same across all driver/motors as these are in
parallel. The current will be 'shared' amoungst however many
driver/motor pairs you have connected.

Tony

Discussion Thread

Weyland 2003-09-12 18:15:35 UTC Clarifications needed - Tim Goldstein 2003-09-12 18:34:54 UTC RE: [CAD_CAM_EDM_DRO] Clarifications needed - washcomp 2003-09-12 18:45:04 UTC Re: Clarifications needed - Weyland 2003-09-12 19:45:08 UTC Re: [CAD_CAM_EDM_DRO] Clarifications needed - Tim Goldstein 2003-09-12 19:55:48 UTC RE: [CAD_CAM_EDM_DRO] Clarifications needed - Weyland 2003-09-12 19:56:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - Weyland 2003-09-12 20:09:51 UTC Re: [CAD_CAM_EDM_DRO] Clarifications needed - Tim Goldstein 2003-09-12 20:40:20 UTC RE: [CAD_CAM_EDM_DRO] Re: Clarifications needed - Jon Elson 2003-09-12 20:42:47 UTC Re: [CAD_CAM_EDM_DRO] Clarifications needed - washcomp 2003-09-12 20:59:18 UTC Re: Clarifications needed - Jon Elson 2003-09-12 21:16:10 UTC Re: [CAD_CAM_EDM_DRO] Clarifications needed - Jon Elson 2003-09-12 21:27:04 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - Harvey White 2003-09-12 21:48:41 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - turbulatordude 2003-09-13 06:12:48 UTC Re: Clarifications needed - 5 volts Graham Stabler 2003-09-13 09:01:17 UTC Re: Clarifications needed - 5 volts Harvey White 2003-09-13 09:37:11 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - 5 volts Keith Bowers 2003-09-13 12:48:21 UTC Re: [CAD_CAM_EDM_DRO] Clarifications needed - Alan Marconett KM6VV 2003-09-13 13:09:37 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - 5 volts Mariss Freimanis 2003-09-13 14:21:11 UTC Re: Clarifications needed - 5 volts Harvey White 2003-09-13 14:29:22 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - 5 volts Weyland 2003-09-13 19:04:38 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - Weyland 2003-09-13 19:32:30 UTC Re: [CAD_CAM_EDM_DRO] Clarifications needed - Weyland 2003-09-13 19:33:57 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - Weyland 2003-09-13 19:40:28 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - Weyland 2003-09-13 19:46:04 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - 5 volts Tim Goldstein 2003-09-13 21:16:52 UTC RE: [CAD_CAM_EDM_DRO] Re: Clarifications needed - Weyland 2003-09-13 21:36:32 UTC Re: [CAD_CAM_EDM_DRO] Re: Clarifications needed - Antonius J.M. Groothuizen 2003-09-13 22:24:37 UTC Re: Clarifications needed - amoss_70 2003-09-13 23:37:20 UTC Re: Clarifications needed - Graham Stabler 2003-09-14 12:13:24 UTC Re: Clarifications needed - 5 volts