Re: [CAD_CAM_EDM_DRO] Re: repeatable vs accurate switch
Posted by
Bob Simon
on 2003-11-06 07:53:02 UTC
At 01:37 PM 11/6/03 +0000, you wrote:
old Hardinge CHNC. The once per rev. sensor was a hall effect device.
-Bob
>I've been considering this myself, and have been thinking of dualThat was the method used by most machine tools with resolvers, including my
>sensors on each axis, one on the table itself for coarse position,
>and another on the back of the motor for fine position.
>
>In a stepper driven environment, this should give repeatability
>limited only by the backlash in the table.
old Hardinge CHNC. The once per rev. sensor was a hall effect device.
-Bob
Discussion Thread
Don Rogers
2003-11-04 21:22:28 UTC
repeatable vs accurate switch
John Haddy
2003-11-04 21:27:56 UTC
RE: [CAD_CAM_EDM_DRO] repeatable vs accurate switch
Doug Fortune
2003-11-04 21:58:57 UTC
Re: [CAD_CAM_EDM_DRO] repeatable vs accurate switch
Mariss Freimanis
2003-11-04 22:11:41 UTC
Re: repeatable vs accurate switch
Marvin Frankel
2003-11-05 01:06:04 UTC
Re: [CAD_CAM_EDM_DRO] repeatable vs accurate switch
Torsten
2003-11-05 01:32:10 UTC
Re: repeatable vs accurate switch
Mark Thompson
2003-11-05 09:20:26 UTC
RE: [CAD_CAM_EDM_DRO] Re: repeatable vs accurate switch
David A. Frantz
2003-11-05 19:31:07 UTC
Re: [CAD_CAM_EDM_DRO] repeatable vs accurate switch
JanRwl@A...
2003-11-05 19:48:50 UTC
Re: [CAD_CAM_EDM_DRO] repeatable vs accurate switch
Mariss Freimanis
2003-11-05 20:29:04 UTC
Re: repeatable vs accurate switch
George Richardson
2003-11-06 07:41:24 UTC
Re: repeatable vs accurate switch
Bob Simon
2003-11-06 07:53:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: repeatable vs accurate switch
Don Rogers
2003-11-06 08:38:38 UTC
Re: repeatable vs accurate switch
Don Rogers
2003-11-06 08:42:46 UTC
Re: repeatable vs accurate switch
Don Rogers
2003-11-06 09:25:59 UTC
Re: repeatable vs accurate switch
Kim Lux
2003-11-06 12:22:01 UTC
Automatic or easier tool changes for R8 mills ?
Mike Gann
2003-11-06 12:53:04 UTC
RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8 mills ?
Kim Lux
2003-11-06 13:10:51 UTC
RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8 mills ?
Mike Gann
2003-11-06 13:21:45 UTC
RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8mills ?
Mike Gann
2003-11-06 13:34:24 UTC
RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8mills ?
Carlos Guillermo
2003-11-06 13:45:43 UTC
RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8mills ?
Kim Lux
2003-11-06 15:15:41 UTC
RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8mills ?
Kim Lux
2003-11-06 15:18:23 UTC
RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8mills ?
tjstraz
2003-11-06 16:23:25 UTC
Re: Automatic or easier tool changes for R8 mills ?
David A. Frantz
2003-11-06 17:16:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: repeatable vs accurate switch
cncgrumpyguy
2003-11-06 18:53:07 UTC
Re: Automatic or easier tool changes for R8 mills ?
mmurray701
2003-11-06 19:34:53 UTC
Re: Automatic or easier tool changes for R8 mills ?
Carlos Guillermo
2003-11-06 20:48:09 UTC
RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8mills?
vavaroutsos
2003-11-06 23:12:19 UTC
Re: Automatic or easier tool changes for R8 mills ?
cncgrumpyguy
2003-11-07 10:33:10 UTC
Re: Automatic or easier tool changes for R8 mills ?
mmurray701
2003-11-07 20:56:18 UTC
Re: Automatic or easier tool changes for R8 mills ?