RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8 mills ?
Posted by
Kim Lux
on 2003-11-06 13:10:51 UTC
Thanks, Mike.
Does anyone know of the exact issue ? I used to subscribe to HSM...
Did the drawbar attach with threads or with a pull nipple ?
Kim
Does anyone know of the exact issue ? I used to subscribe to HSM...
Did the drawbar attach with threads or with a pull nipple ?
Kim
On Thu, 2003-11-06 at 13:52, Mike Gann wrote:
> We use the Royal system - it makes easy and fast tool changes. The tool
> holders are on the expensive side. I know there is also a locking screw you
> should tighten when making a heavy cut with a face mill or even a 5/8"
> endmill. That would slow down the change a little, however we just make
> prototype parts and never push it that hard anyway.
>
> Did you see the article is Home Shop Machinist magazine where Roland
> Friesand (sp?) made a "quick change" tool holder system using a lever and
> cam operated draw bar? I know it was in the last year, but I am not sure
> which issue. You might get some ideas from that.
>
> Hope that helps,
>
> Mike
> -----Original Message-----
> From: Kim Lux [mailto:lux@...]
> Sent: Thursday, November 06, 2003 12:23 PM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8 mills ?
>
> Hi people.
>
> We are getting tired of changing tools with the manual drawbar on our
> R8 equipped CNC'd mill. Does anyone have any experience/ideas with
> implementing a quick or automatic tool change with R8 collets ? The
> first step in the automatic change would be to come up with some sort
> of quick change collet system.
>
> I know of two: the air wrench powered drawbar looseners/tighteners and
> the the Royal system whereby the R8 collet is a holder for another
> collet system.
>
> I'm thinking something along the line of adding a pull nipple on top of
> the R8 collet and pulling it up with an air powered drawbar something
> like how the Cat40 system works.
>
> Failing to find something that works for the R8, our next mill will
> have a Cat something taper...
>
> Thanks.
--
Kim Lux <lux@...>
Discussion Thread
Don Rogers
2003-11-04 21:22:28 UTC
repeatable vs accurate switch
John Haddy
2003-11-04 21:27:56 UTC
RE: [CAD_CAM_EDM_DRO] repeatable vs accurate switch
Doug Fortune
2003-11-04 21:58:57 UTC
Re: [CAD_CAM_EDM_DRO] repeatable vs accurate switch
Mariss Freimanis
2003-11-04 22:11:41 UTC
Re: repeatable vs accurate switch
Marvin Frankel
2003-11-05 01:06:04 UTC
Re: [CAD_CAM_EDM_DRO] repeatable vs accurate switch
Torsten
2003-11-05 01:32:10 UTC
Re: repeatable vs accurate switch
Mark Thompson
2003-11-05 09:20:26 UTC
RE: [CAD_CAM_EDM_DRO] Re: repeatable vs accurate switch
David A. Frantz
2003-11-05 19:31:07 UTC
Re: [CAD_CAM_EDM_DRO] repeatable vs accurate switch
JanRwl@A...
2003-11-05 19:48:50 UTC
Re: [CAD_CAM_EDM_DRO] repeatable vs accurate switch
Mariss Freimanis
2003-11-05 20:29:04 UTC
Re: repeatable vs accurate switch
George Richardson
2003-11-06 07:41:24 UTC
Re: repeatable vs accurate switch
Bob Simon
2003-11-06 07:53:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: repeatable vs accurate switch
Don Rogers
2003-11-06 08:38:38 UTC
Re: repeatable vs accurate switch
Don Rogers
2003-11-06 08:42:46 UTC
Re: repeatable vs accurate switch
Don Rogers
2003-11-06 09:25:59 UTC
Re: repeatable vs accurate switch
Kim Lux
2003-11-06 12:22:01 UTC
Automatic or easier tool changes for R8 mills ?
Mike Gann
2003-11-06 12:53:04 UTC
RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8 mills ?
Kim Lux
2003-11-06 13:10:51 UTC
RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8 mills ?
Mike Gann
2003-11-06 13:21:45 UTC
RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8mills ?
Mike Gann
2003-11-06 13:34:24 UTC
RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8mills ?
Carlos Guillermo
2003-11-06 13:45:43 UTC
RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8mills ?
Kim Lux
2003-11-06 15:15:41 UTC
RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8mills ?
Kim Lux
2003-11-06 15:18:23 UTC
RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8mills ?
tjstraz
2003-11-06 16:23:25 UTC
Re: Automatic or easier tool changes for R8 mills ?
David A. Frantz
2003-11-06 17:16:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: repeatable vs accurate switch
cncgrumpyguy
2003-11-06 18:53:07 UTC
Re: Automatic or easier tool changes for R8 mills ?
mmurray701
2003-11-06 19:34:53 UTC
Re: Automatic or easier tool changes for R8 mills ?
Carlos Guillermo
2003-11-06 20:48:09 UTC
RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8mills?
vavaroutsos
2003-11-06 23:12:19 UTC
Re: Automatic or easier tool changes for R8 mills ?
cncgrumpyguy
2003-11-07 10:33:10 UTC
Re: Automatic or easier tool changes for R8 mills ?
mmurray701
2003-11-07 20:56:18 UTC
Re: Automatic or easier tool changes for R8 mills ?