CAD CAM EDM DRO - Yahoo Group Archive

Re: repeatable vs accurate switch

Posted by Don Rogers

on 2003-11-06 08:38:38 UTC

At 02:29 PM 11/6/03 +0000, you wrote:

>One point it seems NO ONE involved in all this conversation about
>limit-switch accuracy realizes:

Actually Jan the momentum is not an issue for my project. The piece is
moving under spring or gravity load at a rate of less than 0.010" per
minute. This is not a typical limit switch application.

Don

Discussion Thread

Don Rogers 2003-11-04 21:22:28 UTC repeatable vs accurate switch John Haddy 2003-11-04 21:27:56 UTC RE: [CAD_CAM_EDM_DRO] repeatable vs accurate switch Doug Fortune 2003-11-04 21:58:57 UTC Re: [CAD_CAM_EDM_DRO] repeatable vs accurate switch Mariss Freimanis 2003-11-04 22:11:41 UTC Re: repeatable vs accurate switch Marvin Frankel 2003-11-05 01:06:04 UTC Re: [CAD_CAM_EDM_DRO] repeatable vs accurate switch Torsten 2003-11-05 01:32:10 UTC Re: repeatable vs accurate switch Mark Thompson 2003-11-05 09:20:26 UTC RE: [CAD_CAM_EDM_DRO] Re: repeatable vs accurate switch David A. Frantz 2003-11-05 19:31:07 UTC Re: [CAD_CAM_EDM_DRO] repeatable vs accurate switch JanRwl@A... 2003-11-05 19:48:50 UTC Re: [CAD_CAM_EDM_DRO] repeatable vs accurate switch Mariss Freimanis 2003-11-05 20:29:04 UTC Re: repeatable vs accurate switch George Richardson 2003-11-06 07:41:24 UTC Re: repeatable vs accurate switch Bob Simon 2003-11-06 07:53:02 UTC Re: [CAD_CAM_EDM_DRO] Re: repeatable vs accurate switch Don Rogers 2003-11-06 08:38:38 UTC Re: repeatable vs accurate switch Don Rogers 2003-11-06 08:42:46 UTC Re: repeatable vs accurate switch Don Rogers 2003-11-06 09:25:59 UTC Re: repeatable vs accurate switch Kim Lux 2003-11-06 12:22:01 UTC Automatic or easier tool changes for R8 mills ? Mike Gann 2003-11-06 12:53:04 UTC RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8 mills ? Kim Lux 2003-11-06 13:10:51 UTC RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8 mills ? Mike Gann 2003-11-06 13:21:45 UTC RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8mills ? Mike Gann 2003-11-06 13:34:24 UTC RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8mills ? Carlos Guillermo 2003-11-06 13:45:43 UTC RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8mills ? Kim Lux 2003-11-06 15:15:41 UTC RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8mills ? Kim Lux 2003-11-06 15:18:23 UTC RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8mills ? tjstraz 2003-11-06 16:23:25 UTC Re: Automatic or easier tool changes for R8 mills ? David A. Frantz 2003-11-06 17:16:36 UTC Re: [CAD_CAM_EDM_DRO] Re: repeatable vs accurate switch cncgrumpyguy 2003-11-06 18:53:07 UTC Re: Automatic or easier tool changes for R8 mills ? mmurray701 2003-11-06 19:34:53 UTC Re: Automatic or easier tool changes for R8 mills ? Carlos Guillermo 2003-11-06 20:48:09 UTC RE: [CAD_CAM_EDM_DRO] Automatic or easier tool changes for R8mills? vavaroutsos 2003-11-06 23:12:19 UTC Re: Automatic or easier tool changes for R8 mills ? cncgrumpyguy 2003-11-07 10:33:10 UTC Re: Automatic or easier tool changes for R8 mills ? mmurray701 2003-11-07 20:56:18 UTC Re: Automatic or easier tool changes for R8 mills ?