CAD CAM EDM DRO - Yahoo Group Archive

Re: Gecko Bridgeport saga - Gib adjustment?

Posted by Keith Clark
on 2004-09-04 19:31:10 UTC
Ok great, I will try it in the morning. I just picked up a switch
today that I can use nicely. But I am using a 12V unregulated DC
supply from the computer. Do I just connect a wire from Dir input
through a switch to the ground where the black wire from the
computer (I assume ground ) connects?

Thanks
Keith

--- In CAD_CAM_EDM_DRO@yahoogroups.com, Stephen Wille Padnos
<spadnos@s...> wrote:
> Keith Clark wrote:
>
> >Do I put 5 volts to the dir input and then use a switch to turn
it
> >off to get direction? I will use the simple tape measure idea,
> >thanks to both of you. I a similar type to what is recommended
> >according to the oil company.
> >
> >Thanks
> >Keith
> >
> >
> Nope.
>
> You should be supplying 5V to the Gecko at the common pin (pin
12). The
> step and direction lines are active when you contact them to the
ground
> reference of the 5V supply. So, you should connect a switch
between the
> direction input and ground. When the switch is open, it'll be one
> direction (no current flowing through the opto-isolator LED), and
when
> you flip the switch, it'll change direction.
>
> Note that just hooking up a standard signal generator may not
work,
> since you do need to sink current from the step/dir inputs.
>
> - Steve

Discussion Thread

Keith Clark 2004-09-04 05:51:37 UTC Gecko Bridgeport saga continues Andy Wander 2004-09-04 07:14:54 UTC RE: [CAD_CAM_EDM_DRO] Gecko Bridgeport saga continues Keith Clark 2004-09-04 11:11:09 UTC Re: Gecko Bridgeport saga improving Andy Wander 2004-09-04 11:18:53 UTC RE: [CAD_CAM_EDM_DRO] Re: Gecko Bridgeport saga improving vavaroutsos 2004-09-04 11:58:02 UTC Re: Gecko Bridgeport saga improving Keith Clark 2004-09-04 13:15:26 UTC Re: Gecko Bridgeport saga - Gib adjustment? Ron K 2004-09-04 13:24:34 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko Bridgeport saga - Gib adjustment? vavaroutsos 2004-09-04 15:04:50 UTC Re: Gecko Bridgeport saga - Gib adjustment? Keith Clark 2004-09-04 16:26:23 UTC Re: Gecko Bridgeport saga - Gib adjustment? Raymond Heckert 2004-09-04 19:07:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko Bridgeport saga improving Stephen Wille Padnos 2004-09-04 19:08:01 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko Bridgeport saga - Gib adjustment? Keith Clark 2004-09-04 19:26:37 UTC Re: Gecko Bridgeport saga improving Keith Clark 2004-09-04 19:31:10 UTC Re: Gecko Bridgeport saga - Gib adjustment? Stephen Wille Padnos 2004-09-04 19:54:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko Bridgeport saga - Gib adjustment? Jon Elson 2004-09-04 20:46:51 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko Bridgeport saga - Gib adjustment? Keith Clark 2004-09-05 05:17:55 UTC Re: Gecko Bridgeport saga - Gib adjustment? Keith Clark 2004-09-05 05:26:56 UTC Re: Gecko Bridgeport saga - Gib adjustment? vavaroutsos 2004-09-05 09:31:45 UTC Re: Gecko Bridgeport saga - Gib adjustment? Keith Clark 2004-09-05 16:02:16 UTC Re: Gecko Bridgeport saga - Gib adjustment?