Re: Gecko Bridgeport saga - Gib adjustment?
Posted by
Keith Clark
on 2004-09-05 05:17:55 UTC
I am using the red line from a power connection used in the computer
for drives. It is connected to the signal generator which is
designed to be used with stepper motor drives. The 5 vDc to the
Geckos is from the signal generator.
Thanks
Keith
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Stephen Wille Padnos
<spadnos@s...> wrote:
for drives. It is connected to the signal generator which is
designed to be used with stepper motor drives. The 5 vDc to the
Geckos is from the signal generator.
Thanks
Keith
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Stephen Wille Padnos
<spadnos@s...> wrote:
> I hope you're not putting 12V directly to the step/dircommon???!!!??
> Also, where do you get 12V unregulated from a computer? If youhave a
> 12V line that's not between 11.4 and 12.6V, then you need a newpower
> supply. (It should be much closer to 12, but I think the spec is+-5%.)
>you
> They Geckos are set for 5V operation only. You can use 12V, but
> need current limiting resistors if you do it (It's not recommendedin
> any case). I think the current draw for each input is around 10-15 mA,
> and you want 7V across the resistor. That makes for a 4.7K - 6.8Ksince
> resistor in line with each leg. (You need to use one per input
> the total current through the limiting resistor wouldn't be enoughto
> turn them both on at once.)red
>
> If you're using a floppy/hard drive power connector, just use the
> wire instead of yellow.switch
>
> - Steve
>
> Keith Clark wrote:
>
> >Ok great, I will try it in the morning. I just picked up a
> >today that I can use nicely. But I am using a 12V unregulated DCinput
> >supply from the computer. Do I just connect a wire from Dir
> >through a switch to the ground where the black wire from the
> >computer (I assume ground ) connects?
> >
> >Thanks
> >Keith
> >
> >
Discussion Thread
Keith Clark
2004-09-04 05:51:37 UTC
Gecko Bridgeport saga continues
Andy Wander
2004-09-04 07:14:54 UTC
RE: [CAD_CAM_EDM_DRO] Gecko Bridgeport saga continues
Keith Clark
2004-09-04 11:11:09 UTC
Re: Gecko Bridgeport saga improving
Andy Wander
2004-09-04 11:18:53 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko Bridgeport saga improving
vavaroutsos
2004-09-04 11:58:02 UTC
Re: Gecko Bridgeport saga improving
Keith Clark
2004-09-04 13:15:26 UTC
Re: Gecko Bridgeport saga - Gib adjustment?
Ron K
2004-09-04 13:24:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko Bridgeport saga - Gib adjustment?
vavaroutsos
2004-09-04 15:04:50 UTC
Re: Gecko Bridgeport saga - Gib adjustment?
Keith Clark
2004-09-04 16:26:23 UTC
Re: Gecko Bridgeport saga - Gib adjustment?
Raymond Heckert
2004-09-04 19:07:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko Bridgeport saga improving
Stephen Wille Padnos
2004-09-04 19:08:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko Bridgeport saga - Gib adjustment?
Keith Clark
2004-09-04 19:26:37 UTC
Re: Gecko Bridgeport saga improving
Keith Clark
2004-09-04 19:31:10 UTC
Re: Gecko Bridgeport saga - Gib adjustment?
Stephen Wille Padnos
2004-09-04 19:54:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko Bridgeport saga - Gib adjustment?
Jon Elson
2004-09-04 20:46:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko Bridgeport saga - Gib adjustment?
Keith Clark
2004-09-05 05:17:55 UTC
Re: Gecko Bridgeport saga - Gib adjustment?
Keith Clark
2004-09-05 05:26:56 UTC
Re: Gecko Bridgeport saga - Gib adjustment?
vavaroutsos
2004-09-05 09:31:45 UTC
Re: Gecko Bridgeport saga - Gib adjustment?
Keith Clark
2004-09-05 16:02:16 UTC
Re: Gecko Bridgeport saga - Gib adjustment?