Re: [CAD_CAM_EDM_DRO] Re: Gecko Bridgeport saga - Gib adjustment?
Posted by
Stephen Wille Padnos
on 2004-09-04 19:08:01 UTC
Keith Clark wrote:
You should be supplying 5V to the Gecko at the common pin (pin 12). The
step and direction lines are active when you contact them to the ground
reference of the 5V supply. So, you should connect a switch between the
direction input and ground. When the switch is open, it'll be one
direction (no current flowing through the opto-isolator LED), and when
you flip the switch, it'll change direction.
Note that just hooking up a standard signal generator may not work,
since you do need to sink current from the step/dir inputs.
- Steve
>Do I put 5 volts to the dir input and then use a switch to turn itNope.
>off to get direction? I will use the simple tape measure idea,
>thanks to both of you. I a similar type to what is recommended
>according to the oil company.
>
>Thanks
>Keith
>
>
You should be supplying 5V to the Gecko at the common pin (pin 12). The
step and direction lines are active when you contact them to the ground
reference of the 5V supply. So, you should connect a switch between the
direction input and ground. When the switch is open, it'll be one
direction (no current flowing through the opto-isolator LED), and when
you flip the switch, it'll change direction.
Note that just hooking up a standard signal generator may not work,
since you do need to sink current from the step/dir inputs.
- Steve
Discussion Thread
Keith Clark
2004-09-04 05:51:37 UTC
Gecko Bridgeport saga continues
Andy Wander
2004-09-04 07:14:54 UTC
RE: [CAD_CAM_EDM_DRO] Gecko Bridgeport saga continues
Keith Clark
2004-09-04 11:11:09 UTC
Re: Gecko Bridgeport saga improving
Andy Wander
2004-09-04 11:18:53 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko Bridgeport saga improving
vavaroutsos
2004-09-04 11:58:02 UTC
Re: Gecko Bridgeport saga improving
Keith Clark
2004-09-04 13:15:26 UTC
Re: Gecko Bridgeport saga - Gib adjustment?
Ron K
2004-09-04 13:24:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko Bridgeport saga - Gib adjustment?
vavaroutsos
2004-09-04 15:04:50 UTC
Re: Gecko Bridgeport saga - Gib adjustment?
Keith Clark
2004-09-04 16:26:23 UTC
Re: Gecko Bridgeport saga - Gib adjustment?
Raymond Heckert
2004-09-04 19:07:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko Bridgeport saga improving
Stephen Wille Padnos
2004-09-04 19:08:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko Bridgeport saga - Gib adjustment?
Keith Clark
2004-09-04 19:26:37 UTC
Re: Gecko Bridgeport saga improving
Keith Clark
2004-09-04 19:31:10 UTC
Re: Gecko Bridgeport saga - Gib adjustment?
Stephen Wille Padnos
2004-09-04 19:54:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko Bridgeport saga - Gib adjustment?
Jon Elson
2004-09-04 20:46:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko Bridgeport saga - Gib adjustment?
Keith Clark
2004-09-05 05:17:55 UTC
Re: Gecko Bridgeport saga - Gib adjustment?
Keith Clark
2004-09-05 05:26:56 UTC
Re: Gecko Bridgeport saga - Gib adjustment?
vavaroutsos
2004-09-05 09:31:45 UTC
Re: Gecko Bridgeport saga - Gib adjustment?
Keith Clark
2004-09-05 16:02:16 UTC
Re: Gecko Bridgeport saga - Gib adjustment?