Re: Minimum reasonable computer speed?
Posted by
Torsten
on 2005-01-27 23:50:22 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Codesuidae <codesuidae@c...>
wrote:
do a reasonable job on a 486 Pc.
You should figure out the maximum stepcount required by your motors
and machine.
How fast are you gone run it and how many steps need to be put out
to get to that speed.
(Multiy stepping?, leadscrew ratio?, pulleys?)
About 10khz will be no problem if you need more you may want to
look for a faster Pc, a older Pentium is easy to come by these days.
The advantage of a faster Pc is that it is likely to run a more
consistent Pulse count it would be smuther at higher rates.
Good Luck
wrote:
> Whats the minimum reasonable computer platform for controllingsomething
> like a 4 axis xylotec board?sufficent,
>
> I've got an old 486 (about 33mhz), which I think should be
> but I just want to double check.Yes there are several dos and linux controller programs that will
> Is there any advantage to running something faster?
>
> Thanks,
> CS
do a reasonable job on a 486 Pc.
You should figure out the maximum stepcount required by your motors
and machine.
How fast are you gone run it and how many steps need to be put out
to get to that speed.
(Multiy stepping?, leadscrew ratio?, pulleys?)
About 10khz will be no problem if you need more you may want to
look for a faster Pc, a older Pentium is easy to come by these days.
The advantage of a faster Pc is that it is likely to run a more
consistent Pulse count it would be smuther at higher rates.
Good Luck
Discussion Thread
Codesuidae
2005-01-27 15:25:12 UTC
Minimum reasonable computer speed?
Robert Campbell
2005-01-27 15:48:50 UTC
Re: [CAD_CAM_EDM_DRO] Minimum reasonable computer speed?
R Rogers
2005-01-27 15:53:24 UTC
Re: [CAD_CAM_EDM_DRO] Minimum reasonable computer speed?
Roy J. Tellason
2005-01-27 16:47:07 UTC
Re: [CAD_CAM_EDM_DRO] Minimum reasonable computer speed?
Stephen Wille Padnos
2005-01-27 16:51:36 UTC
Re: [CAD_CAM_EDM_DRO] Minimum reasonable computer speed?
R Rogers
2005-01-27 17:46:00 UTC
Re: [CAD_CAM_EDM_DRO] Minimum reasonable computer speed?
Robert Campbell
2005-01-27 18:14:20 UTC
Re: [CAD_CAM_EDM_DRO] Minimum reasonable computer speed?
Scott L Golden
2005-01-27 18:37:46 UTC
Re: [CAD_CAM_EDM_DRO] Minimum reasonable computer speed?
turbulatordude
2005-01-27 18:40:23 UTC
Re: Minimum reasonable computer speed?
codeSuidae
2005-01-27 21:52:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Minimum reasonable computer speed?
JanRwl@A...
2005-01-27 23:01:36 UTC
Re: [CAD_CAM_EDM_DRO] Minimum reasonable computer speed?
Torsten
2005-01-27 23:50:22 UTC
Re: Minimum reasonable computer speed?
Ron Ginger
2005-01-28 06:20:17 UTC
Re: Minimum reasonable computer speed?
Richard Garnish
2005-01-28 06:30:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Minimum reasonable computer speed?
cnc_4_me
2005-01-28 06:59:15 UTC
Re: Minimum reasonable computer speed?
R Rogers
2005-01-28 07:11:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Minimum reasonable computer speed?
turbulatordude
2005-01-28 07:24:04 UTC
Re: Minimum reasonable computer speed?
Fred Smith
2005-01-28 10:13:37 UTC
Re: Minimum reasonable computer speed?
Alan Marconett
2005-01-28 11:00:48 UTC
Re: [CAD_CAM_EDM_DRO] Minimum reasonable computer speed?
JanRwl@A...
2005-01-28 22:25:37 UTC
Re: [CAD_CAM_EDM_DRO] Minimum reasonable computer speed?
David A. Frantz
2005-01-29 08:18:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Minimum reasonable computer speed?