CAD CAM EDM DRO - Yahoo Group Archive

Re: Gearhead motors ? future drives ?

Posted by Fred Smith
on 2005-05-16 08:08:05 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "turbulatordude"
<dave_mucha@y...> wrote:
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "vrsculptor"
<vrsculptor@h...>
> wrote:
> > Dave,
> > I don't disagree at all but there are always tradeoffs. If you
use
> > the 10X multiplier the G340 will fault if it the motor is off
by
> > off by +/- 13 counts (10 X 13 = 130). Ask me how I know :) If
you
> > derate the machine enough this doesn't matter. If you put on
lower
> > resolution encoders the +/- 1 count servo dance can have an
effect
> > on finish.
> >
> > I'm hoping that I can use Mariss' un-stop-able stepper drive
logic
> > to control the G320. The G100 should not care if it is a stepper
or
> > servo as long as it get encoder pulses.
> >
> > Roger
>
>
> Funny, I chose not to use the multiplier for pretty much the same
reason.
>


DeskCNC has been delivering 125,000, smooth, steps per second for
the better part of a year, and 45,000 for 2 years before that.

That gives you what? 600 ipm.

Fred Smith - IMService
http://www.cadcamcadcam.com/hobby

Discussion Thread

turbulatordude 2005-05-14 13:27:43 UTC Gearhead motors ? R Rogers 2005-05-14 13:52:30 UTC Re: [CAD_CAM_EDM_DRO] Gearhead motors ? KM6VV 2005-05-14 13:53:54 UTC Re: [CAD_CAM_EDM_DRO] Gearhead motors ? Polaraligned 2005-05-14 16:31:52 UTC Re: Gearhead motors ? turbulatordude 2005-05-14 18:57:02 UTC Re: Gearhead motors ? future drives ? washcomp 2005-05-14 19:47:14 UTC Re: Gearhead motors ? future drives ? R Rogers 2005-05-15 07:02:43 UTC Re: [CAD_CAM_EDM_DRO] Re: Gearhead motors ? turbulatordude 2005-05-15 07:26:14 UTC Re: Gearhead motors ? future drives ? cnc_4_me 2005-05-15 07:44:36 UTC Mod Bus was: Re: Gearhead motors ? future drives ? DP 2005-05-15 08:07:11 UTC Re: [CAD_CAM_EDM_DRO] Mod Bus was: Re: Gearhead motors ? future drives ? turbulatordude 2005-05-15 08:23:15 UTC Mod Bus was: Re: Gearhead motors ? future drives ? vrsculptor 2005-05-15 13:17:55 UTC Re: Gearhead motors ? future drives ? turbulatordude 2005-05-15 18:27:42 UTC Re: Gearhead motors ? future drives ? vrsculptor 2005-05-15 20:00:51 UTC Re: Gearhead motors ? future drives ? turbulatordude 2005-05-15 22:09:39 UTC Re: Gearhead motors ? future drives ? Polaraligned 2005-05-16 03:22:26 UTC Encoder resolution Polaraligned 2005-05-16 03:28:35 UTC Re: Gearhead motors ? Polaraligned 2005-05-16 03:33:32 UTC Re: Encoder resolution Les Newell 2005-05-16 05:58:29 UTC Re: [CAD_CAM_EDM_DRO] Re: Encoder resolution turbulatordude 2005-05-16 06:52:00 UTC Re: Gearhead motors ? next-gen software Fred Smith 2005-05-16 08:08:05 UTC Re: Gearhead motors ? future drives ? m0nkey0ne 2005-05-16 11:43:04 UTC Re: Gearhead motors ? future drives ? turbulatordude 2005-05-16 13:59:27 UTC Re: Gearhead motors ? future drives ? Polaraligned 2005-05-16 14:04:08 UTC Re: Encoder resolution caudlet 2005-05-16 14:24:20 UTC Re: Encoder resolution Les Newell 2005-05-16 15:05:42 UTC Re: [CAD_CAM_EDM_DRO] Re: Encoder resolution Jon Elson 2005-05-16 18:27:18 UTC Re: [CAD_CAM_EDM_DRO] Re: Encoder resolution Jon Elson 2005-05-16 18:33:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Encoder resolution