Re: BOSS5 Where to plug the Geckos???
Posted by
braidmeister
on 2005-06-25 10:38:08 UTC
I have posted some pics of the current state of affairs...Many thanks
so far for all of the help. On the page you will see where I am
now...where I think I am going and hopefully you can tell me where to
go next: http://www.ibild.com/BP.htm
Thanks!
-Brady
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Les Newell <lesnewell@h...>
wrote:
so far for all of the help. On the page you will see where I am
now...where I think I am going and hopefully you can tell me where to
go next: http://www.ibild.com/BP.htm
Thanks!
-Brady
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Les Newell <lesnewell@h...>
wrote:
> Hi Brady,then
>
> When I did my mill I scrapped the computer cabinet completely. I
> moved the power cabinet round to the side and fitted everything inthat.
> You don't need the three big chokes in the bottom of the cabinet orthe
> great big 3 phase transformer in the middle. Believe it or not theyare
> the stepper power supply!. When I moved the cabiet I had to plug aif
> couple of holes in the base and tap one new one. The top mount fits
> you turn it upside down. There is just enough room to fit acomputer in
> there as well but you need to get one with a small case.power
>
> You can use the big 110V transformer in the top of your cabinet to
> the steppers/servos if you rewire it to twice your actual supplyfor
> voltage. For instance my supply is 230V so I wired the transformer
> 460V. This halves the output voltage, giving 55VAC.for
>
> Les
>
> braidmeister wrote:
>
> >Well I took the plunge yesterday and gutted the computer cabinet
> >the most part. I only had to cut 2 wires, which were soldered tothe
> >transformer buried in the bottom. On a side noe...can anyone tellme
> >the right way to discharge those big capacitors??? I was sweatingthe
> >while disconnecting them fearing getting zapped. :)
> >
> >I still have to pull the pendant off the top and pull all of those
> >skinny 24ga wires thru. I did leave the relays at the bottom of
> >cabinet in place. These are to turn the way lube on??? What arethese
> >for exactly? Still have to pull the transistor plates off of thebig
> >sink and do a few other odds and ends...torid
> >
> >I am thinking at this point that I might take the 2 55v/800VA
> >transformers that I bought for the servos and mate them with somedecide
> >caps that I pulled out of the cabinet. That way if/when I do
> >to run the servos (or my 4th axis) I know that I'll have enough
> >cookies to run everything.
> >
> >If time permits (been so busy working!) I'd like to do full
> >documentation on the conversion using Geckos so that others can
> >follow along...and know that their machine will work in the end! I
> >don't believe that you have to spend $5k+ on a prepackaged servo
> >upgrade (or $2k for a stepper upgrade kit) to get the machine
> >running.
> >
> >Thanks for all the help thus far,
> >-Brady
> >
> >
Discussion Thread
braidmeister
2005-06-23 16:55:31 UTC
BOSS5 Where to plug the Geckos???
Keith Clark
2005-06-23 20:25:45 UTC
Re: BOSS5 Where to plug the Geckos???
braidmeister
2005-06-23 20:46:20 UTC
Re: BOSS5 Where to plug the Geckos???
Keith Clark
2005-06-24 04:15:47 UTC
Re: BOSS5 Where to plug the Geckos???
braidmeister
2005-06-25 05:45:56 UTC
Re: BOSS5 Where to plug the Geckos???
Alex Holden
2005-06-25 06:35:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: BOSS5 Where to plug the Geckos???
Les Newell
2005-06-25 08:14:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: BOSS5 Where to plug the Geckos???
braidmeister
2005-06-25 10:38:08 UTC
Re: BOSS5 Where to plug the Geckos???
Les Newell
2005-06-25 12:14:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: BOSS5 Where to plug the Geckos???
turbulatordude
2005-06-25 12:33:55 UTC
Re: BOSS5 Where to plug the Geckos???
braidmeister
2005-06-25 13:14:50 UTC
Re: BOSS5 Where to plug the Geckos???
braidmeister
2005-06-25 13:21:03 UTC
Re: BOSS5 Where to plug the Geckos???
Les Newell
2005-06-25 14:02:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: BOSS5 Where to plug the Geckos???
braidmeister
2005-06-25 14:15:43 UTC
Re: BOSS5 Where to plug the Geckos???
Les Newell
2005-06-25 17:57:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: BOSS5 Where to plug the Geckos???
Keith Clark
2005-06-25 20:47:09 UTC
Re: BOSS5 Where to plug the Geckos???
braidmeister
2005-06-25 21:22:22 UTC
Re: BOSS5 Where to plug the Geckos???
Polaraligned
2005-06-26 05:03:24 UTC
Re: BOSS5 Where to plug the Geckos???
Polaraligned
2005-06-26 05:07:11 UTC
Re: BOSS5 Where to plug the Geckos???
Polaraligned
2005-06-26 05:16:41 UTC
Re: BOSS5 Where to plug the Geckos???
Alex Holden
2005-06-26 06:25:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: BOSS5 Where to plug the Geckos???
braidmeister
2005-06-26 06:57:56 UTC
Re: BOSS5 Where to plug the Geckos???
caedave
2005-06-26 14:16:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: BOSS5 Where to plug the Geckos???
Jon Elson
2005-06-27 22:03:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: BOSS5 Where to plug the Geckos???