Re: [CAD_CAM_EDM_DRO] Re: LPT1
Posted by
JanRwl@A...
on 2005-08-07 21:24:49 UTC
In a message dated 8/7/2005 7:31:48 P.M. Central Daylight Time,
dave_mucha@... writes:
You can get 5v from the PC if the PC has 5V, but if you have less, that may
be a problem.<<
On newer PC's, you can steal 5VDC from a USB port. If you don't have those,
there is almost-surely an unused "disk-drive power-plug" inside (the white
things with the red, yellow, and two black wires). The Red wire should be 5
VDC. The blacks are Gnd. (-ve). The yeller is 12 VDC.
[Non-text portions of this message have been removed]
dave_mucha@... writes:
You can get 5v from the PC if the PC has 5V, but if you have less, that may
be a problem.<<
On newer PC's, you can steal 5VDC from a USB port. If you don't have those,
there is almost-surely an unused "disk-drive power-plug" inside (the white
things with the red, yellow, and two black wires). The Red wire should be 5
VDC. The blacks are Gnd. (-ve). The yeller is 12 VDC.
[Non-text portions of this message have been removed]
Discussion Thread
stcnc2000
2005-08-07 11:30:01 UTC
LPT1
Robert Campbell
2005-08-07 11:42:26 UTC
Re: [CAD_CAM_EDM_DRO] LPT1
stcnc2000
2005-08-07 12:05:53 UTC
Re: LPT1
Steve Stallings
2005-08-07 12:38:04 UTC
Re: LPT1
Robert Campbell
2005-08-07 12:50:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPT1
thinkcnc@w...
2005-08-07 13:01:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPT1
caudlet
2005-08-07 15:02:42 UTC
Re: LPT1
thinkcnc@w...
2005-08-07 15:10:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPT1
turbulatordude
2005-08-07 15:19:12 UTC
Re: LPT1
thinkcnc@w...
2005-08-07 15:30:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPT1
JanRwl@A...
2005-08-07 15:38:24 UTC
Re: [CAD_CAM_EDM_DRO] LPT1
turbulatordude
2005-08-07 17:30:46 UTC
Re: LPT1
JanRwl@A...
2005-08-07 21:24:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPT1
Keith Bucklitch
2005-08-08 14:01:21 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPT1
c_holm10017
2005-08-08 14:11:59 UTC
Re: LPT1
Andy Wander
2005-08-08 14:19:46 UTC
RE: [CAD_CAM_EDM_DRO] Re: LPT1
turbulatordude
2005-08-08 14:27:36 UTC
Re: LPT1
JCullins
2005-08-08 14:45:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPT1
Mike Delany
2005-08-08 15:09:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPT1
JanRwl@A...
2005-08-08 17:47:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPT1
Jon Elson
2005-08-08 19:13:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPT1
Keith Bucklitch
2005-08-09 09:26:26 UTC
RE: [CAD_CAM_EDM_DRO] Re: LPT1
Keith Bucklitch
2005-08-09 09:26:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPT1
Keith Bucklitch
2005-08-09 09:26:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPT1
George Taylor, IV
2005-08-09 13:15:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPT1
Keith Bucklitch
2005-08-09 14:41:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPT1
Andy Wander
2005-08-09 18:09:48 UTC
RE: [CAD_CAM_EDM_DRO] Re: LPT1
Aahz.
2005-08-09 18:58:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPT1
JanRwl@A...
2005-08-09 22:12:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPT1
George Taylor, IV
2005-08-09 22:24:01 UTC
RE: [CAD_CAM_EDM_DRO] Re: LPT1
Keith Bucklitch
2005-08-10 01:40:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPT1
Marv Frankel
2005-08-10 03:12:13 UTC
Re: LPT1
Keith Bucklitch
2005-08-10 09:57:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: LPT1