CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Lithium Grease

Posted by cnc002@a...
on 2005-10-15 13:56:46 UTC
In a message dated 10/15/2005 2:30:23 P.M. Eastern Daylight Time,
carlcnc@... writes:

if you cut much mdf or pitchy woods,do NOT use wd40 as lube!

Carl
>



Actually, NEVER use WD40 as a lube. It will actually "dry out" the natural
lubricating properties of many metals. It is designed as a cleaner/penetrant
and temporary lubricant only. I have seen machines costing as much as a
Million dollars shut down over a few months because the maint. people were
cleaning the screws and/or guide rails on them with WD40 and thought that was all
they needed in the way of lubricant. Over the past 20+ years I have been
doing industrial woodworking machinery installation, repair, service etc., plain
old 30W non-detergent motor oil or "turbine oil" ( you can often find the
"turbine oil" in small plastic squeeze applicators at auto stores or appliance
parts stores ) work the best where oiling is required.

Well, my 2 cents worth, hope that helps some.

Oh, and again, mineral spirits should cut that Lithium grease, You might
need to do some brushing but be careful, NEVER, use a steel brush, always a
brass or just stiff bristled one.

Randy A.


[Non-text portions of this message have been removed]

Discussion Thread

jymmm 2005-10-14 11:51:29 UTC Lithium Grease juan gelt 2005-10-14 12:43:41 UTC Re: [CAD_CAM_EDM_DRO] Lithium Grease cnc002@a... 2005-10-14 15:02:34 UTC Re: [CAD_CAM_EDM_DRO] Lithium Grease jymmm 2005-10-14 18:50:45 UTC Re: Lithium Grease Jon Elson 2005-10-14 21:22:56 UTC Re: [CAD_CAM_EDM_DRO] Lithium Grease jymmm 2005-10-14 22:09:21 UTC Re: Lithium Grease carlcnc 2005-10-15 11:27:40 UTC Re: Lithium Grease cnc002@a... 2005-10-15 13:56:46 UTC Re: [CAD_CAM_EDM_DRO] Re: Lithium Grease Jymmm 2005-10-16 09:06:13 UTC Re: Lithium Grease cnc002@a... 2005-10-16 12:30:41 UTC Re: [CAD_CAM_EDM_DRO] Re: Lithium Grease Randy Brown 2005-10-16 16:20:03 UTC RE: [CAD_CAM_EDM_DRO] Re: Lithium Grease Babar 2005-10-16 20:24:33 UTC Step and Dir to motor pulses.....????? turbulatordude 2005-10-16 23:52:42 UTC Re: Step and Dir to motor pulses.....????? Chris Horne 2005-10-17 04:15:44 UTC Re: Lithium Grease cnc002@a... 2005-10-17 06:33:00 UTC Re: [CAD_CAM_EDM_DRO] Re: Lithium Grease cnc002@a... 2005-10-17 06:34:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Lithium Grease pavel59 2005-10-17 07:25:35 UTC Re: Lithium Grease cnc002@a... 2005-10-17 07:58:56 UTC Re: [CAD_CAM_EDM_DRO] Re: Lithium Grease pavel59 2005-10-17 08:24:53 UTC Re: Lithium Grease cnc002@a... 2005-10-17 10:14:46 UTC Re: [CAD_CAM_EDM_DRO] Re: Lithium Grease Roy J. Tellason 2005-10-17 14:24:36 UTC Re: [CAD_CAM_EDM_DRO] Re: Step and Dir to motor pulses.....????? John Johnson 2005-10-17 19:36:21 UTC Re: [CAD_CAM_EDM_DRO] Re: Lithium Grease Babar 2005-10-17 20:45:37 UTC Re: [CAD_CAM_EDM_DRO] Re: Step and Dir to motor pulses.....????? cnc002@a... 2005-10-18 06:04:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Lithium Grease John Johnson 2005-10-18 07:42:53 UTC Re: [CAD_CAM_EDM_DRO] Re: Lithium Grease John Johnson 2005-10-18 07:49:26 UTC Re: [CAD_CAM_EDM_DRO] Re: Lithium Grease OT John Johnson 2005-10-18 07:51:38 UTC Re: [CAD_CAM_EDM_DRO] Re: Lithium Grease OT Jymmm 2005-10-18 11:16:40 UTC Re: Lithium Grease pavel59 2005-10-18 12:28:34 UTC Re: Lithium Grease