Re: 1720XMTC shoptask z axis Ballscrews
Posted by
danmauch
on 2011-01-01 18:32:26 UTC
I built all of Chuck McGhee's CNC units and since he only lived about 25 miles from me , I went down to his shop on several occasions to set up new controls or to fix some problems he had converting from Maxnc software to Mach1, 2 and 3.
As I recall he used a dual ballscrew with a 300 oz in stepper motor driving two pulleys that were bored to fit ball nuts. The nuts rotated while the ballscrew were stationary but when connected to his quill would raise and lower it. But I am not absoluetely positive. I will email chuck and see if he can send me the picture. He is no longer working with his machines as his healt prevents him from setting it up in his new location.
Dan Mauch
www.camtronics-cnc.com
dmauch@...
low cost CNC systems using Gecko products.
Kits, assembled systems, custom systems.
As I recall he used a dual ballscrew with a 300 oz in stepper motor driving two pulleys that were bored to fit ball nuts. The nuts rotated while the ballscrew were stationary but when connected to his quill would raise and lower it. But I am not absoluetely positive. I will email chuck and see if he can send me the picture. He is no longer working with his machines as his healt prevents him from setting it up in his new location.
Dan Mauch
www.camtronics-cnc.com
dmauch@...
low cost CNC systems using Gecko products.
Kits, assembled systems, custom systems.
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Andy Wander <awander@...> wrote:
>
> HI Jimmy:
>
> I am also looking for more details on Chuck McGhee's conversion. I have only seen the photos at his old website, which appears to be defunct. I will keep you posted if I fid anything.
>
>
> Andy Wander
>
>
>
> -----Original Message-----
> From: CAD_CAM_EDM_DRO@yahoogroups.com [mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of jimmy_staton
> Sent: Friday, December 31, 2010 8:03 PM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: [CAD_CAM_EDM_DRO] 1720XMTC shoptask z axis Ballscrews
>
> I have an old Shoptask 1720XMTC that I'm converting to CNC I have the X & Y axis
> mostly done.
>
> At one time I saw a guy Ex. Boeing Machines (Chuck) maybe; he's on the Shoptask
> site under projects, that had converted the Z axis to a ballscrew feed using 2 ballscrews to eliminate that horrible z axis setup feed. Would anyone have anymore information on how he did it.
>
> I realize I'm reaching but I've searched all over try to find more information on how it was done.
>
> Thanks
> Jimmy
>
>
>
>
> ------------------------------------
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
> Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
> Yahoo! Groups Links
>
>
>
> This communication including any attachments, are intended
> for the exclusive use of the addressee(s) and contains
> confidential or copyrighted materials. Duplication,
> distribution or reproduction is strictly prohibited by law
> without written permission of Verrex
>
Discussion Thread
jimmy_staton
2010-12-31 17:03:15 UTC
1720XMTC shoptask z axis Ballscrews
Andy Wander
2011-01-01 16:40:02 UTC
RE: [CAD_CAM_EDM_DRO] 1720XMTC shoptask z axis Ballscrews
Ron Thompson
2011-01-01 16:44:47 UTC
Re: [CAD_CAM_EDM_DRO] 1720XMTC shoptask z axis Ballscrews
Ron Thompson
2011-01-01 16:46:00 UTC
Re: [CAD_CAM_EDM_DRO] 1720XMTC shoptask z axis Ballscrews
Andy Wander
2011-01-01 16:51:49 UTC
RE: [CAD_CAM_EDM_DRO] 1720XMTC shoptask z axis Ballscrews
danmauch
2011-01-01 18:32:26 UTC
Re: 1720XMTC shoptask z axis Ballscrews
danmauch
2011-01-01 19:14:08 UTC
Re: 1720XMTC shoptask z axis Ballscrews
jimmy_staton
2011-01-02 06:47:07 UTC
Re: 1720XMTC shoptask z axis Ballscrews
jimmy_staton
2011-01-02 12:52:54 UTC
Re: 1720XMTC shoptask z axis Ballscrews
Ron Thompson
2011-01-02 13:06:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: 1720XMTC shoptask z axis Ballscrews
jimmy_staton
2011-01-02 13:11:29 UTC
Re: 1720XMTC shoptask z axis Ballscrews
Ron Thompson
2011-01-02 13:17:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: 1720XMTC shoptask z axis Ballscrews
jimmy_staton
2011-01-02 13:32:14 UTC
Re: 1720XMTC shoptask z axis Ballscrews
danmauch
2011-01-03 08:32:37 UTC
Re: 1720XMTC shoptask z axis Ballscrews
jimmy_staton
2011-01-03 12:57:10 UTC
Re: 1720XMTC shoptask z axis Ballscrews
danmauch
2011-01-04 07:20:59 UTC
Re: 1720XMTC shoptask z axis Ballscrews
William Thomas
2011-01-05 13:22:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: 1720XMTC shoptask z axis Ballscrews
danmauch
2011-01-10 08:54:10 UTC
Re: 1720XMTC shoptask z axis Ballscrews
jimmy_staton
2011-01-21 14:37:39 UTC
Re: 1720XMTC shoptask z axis Ballscrews
Andy Wander
2011-01-21 21:14:32 UTC
RE: [CAD_CAM_EDM_DRO] Re: 1720XMTC shoptask z axis Ballscrews
jimmy_staton
2011-01-22 07:28:53 UTC
Re: 1720XMTC shoptask z axis Ballscrews
danmauch
2011-01-22 08:45:35 UTC
Re: 1720XMTC shoptask z axis Ballscrews
Andy Wander
2011-01-22 10:12:22 UTC
RE: [CAD_CAM_EDM_DRO] Re: 1720XMTC shoptask z axis Ballscrews
jimmy_staton
2011-01-22 12:41:26 UTC
Re: 1720XMTC shoptask z axis Ballscrews
jimmy_staton
2011-01-22 12:44:21 UTC
Re: 1720XMTC shoptask z axis Ballscrews
Andy Wander
2011-01-22 13:29:53 UTC
RE: [CAD_CAM_EDM_DRO] Re: 1720XMTC shoptask z axis Ballscrews
Andy Wander
2011-01-23 18:57:52 UTC
RE: [CAD_CAM_EDM_DRO] Re: 1720XMTC shoptask z axis Ballscrews
jimmy_staton
2011-01-23 19:27:48 UTC
Re: 1720XMTC shoptask z axis Ballscrews
Andy Wander
2011-01-23 20:23:30 UTC
RE: [CAD_CAM_EDM_DRO] Re: 1720XMTC shoptask z axis Ballscrews
Andy
2011-02-14 19:04:15 UTC
Re: 1720XMTC shoptask z axis Ballscrews
jimmy_staton
2011-04-11 17:02:07 UTC
Re: 1720XMTC shoptask z axis Ballscrews
Bloy
2012-10-15 12:25:48 UTC
Re: 1720XMTC shoptask z axis Ballscrews