Re: 1720XMTC shoptask z axis Ballscrews

--- In CAD_CAM_EDM_DRO@yahoogroups.com, Andy Wander <awander@...> wrote:
>
> Hey, Jimmy:
>
> Wondering if you could give me some more info on that unit:
>
> -how many teeth on the motor pulleys?
>
> -how many teeth on the ballscrew pulleys?
>
> -TPI on the ballscrews?
>
> Thanks for any help you can give,
>
>
> Andy Wander
>
>
> -----Original Message-----
> From: CAD_CAM_EDM_DRO@yahoogroups.com [mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of jimmy_staton
> Sent: Saturday, January 22, 2011 3:44 PM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: [CAD_CAM_EDM_DRO] Re: 1720XMTC shoptask z axis Ballscrews
>
> I ask Chuck that question and he said no! I have to say that with all the bearings and
> belts not to mention the stepper involved there is a fair amount of drag there.
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, Andy Wander <awander@> wrote:
> >
> > Ya' know, when I first CNC'd my machine, I carefully constructed the controller box to allow me to disconnect the motors and run it manually. After about 2 years, I think I did ONE manual operation. So I don't think I will need the hand crank.
> >
> > I was wondering if the Z axis will fall down of it's own weight when the machine is powered down...
> >
> > And I like your idea about a stepped base plate! Thanks!
> >
> >
> > Andy Wander
> >
> > (PS: Sorry, Steve. I also took a shower and ate breakfast today, taking yet more time away from DIY-CNC moderation duties...)
> >
> > -----Original Message-----
> > From: CAD_CAM_EDM_DRO@yahoogroups.com [mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of jimmy_staton
> > Sent: Saturday, January 22, 2011 10:29 AM
> > To: CAD_CAM_EDM_DRO@yahoogroups.com
> > Subject: [CAD_CAM_EDM_DRO] Re: 1720XMTC shoptask z axis Ballscrews
> >
> > You would have to accommodate the crank handle either on the motor or idler to allow
> > hand adjustment. I supposed you could make a more elaborate base plate also, the sides where the screw are attached could be about 2" higher, between that and the tooling sticking down from the spindle you'd have some more clearance.
> >
> >
> > --- In CAD_CAM_EDM_DRO@yahoogroups.com, Andy Wander <awander@> wrote:
> > >
> > > Thanks for that, Jimmy.
> > >
> > > I am looking at the design, and I like it EXCEPT for the huge plate that attaches to the bottom of the Z ram. I am afraid that with that thing sticking forward and back that far, I will have trouble clearing things like my CN dividing head, when doing rotary work.
> > >
> > > I guess I could rotate the table itself, and mount the dividing head so it is to the right or left of the spindle in stead of behind it, but I am thinking about a way to move the ballscrews closer to the spindle centerline.
> > >
> > > At first glance, I anticipate trouble with the belts hitting the headstock casting, but I wonder if it would work to use idlers to route the belts around the casting?
> > >
> > > Or what if the motor/belts, etc were arranged as follows:
> > > -move the rear and the front ballscrews as close as possible to the headstock(keeping them in front and behind)
> > > -mount the drive motor directly to the right(X++) of the rear ballscrew.
> > > -drive the rear ballscrew directly from the motor
> > > -draw a line from the motor in the Y-- direction; draw another line from the front ballscrew in the X++ direction. Mount a double idler pulley at the intersection of those 2 lines.
> > > -drive the idler from the double pulley on the mtor, and drive the front ballscrew from the double idler pulley. Like this:
> > >
> > > b-------m
> > > |
> > > S |
> > > |
> > > b-------I
> > >
> > > where "b" is a ballscrew
> > > "m" is the drive motor
> > > "S" is the spindle
> > > "I" is the douboleidelr pulley
> > >
> > > Andy Wander, CTS, TCE I / TCE II
> > > Vice President, Engineering
> > >
> > > Verrex Corporation
> > > Americas Headquarters
> > > 1130 Route 22 West
> > > Mountainside, NJ 07092 USA
> > > Direct: +1 908 664 8353
> > > Tel: +1 908 232 7000
> > > Mobile: +1 610 389 4819
> > > awander@
> > > www.verrex.com
> > >
> > > EMEA/Verrex Limited: +44 (0) 1992 667 000
> > > Asia Pacific/Verrex Asia Limited: +852 3713 4200
> > >
> > > Global Conferencing & Communication Solutions
> > > New York | Boston | Tampa | London | Hong Kong
> > >
> > > Please join us in working & living environmentally responsibly. Consider the environment before printing this email.
> > >
> > >
> > > -----Original Message-----
> > > From: CAD_CAM_EDM_DRO@yahoogroups.com [mailto:CAD_CAM_EDM_DRO@yahoogroups.com] On Behalf Of jimmy_staton
> > > Sent: Friday, January 21, 2011 5:37 PM
> > > To: CAD_CAM_EDM_DRO@yahoogroups.com
> > > Subject: [CAD_CAM_EDM_DRO] Re: 1720XMTC shoptask z axis Ballscrews
> > >
> > > Ok, with Dan's help I have talked to Chuck and also acquired one of the Z-Axis rigs that
> > > Chuck built before moving. I'll post some information but it will only make sense if you
> > > reference the photos listed under Chuck McGhee (Shoptask) in the photo section.
> > >
> > > Photo link:
> > > http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/photos/album/1886719219/pic/1656316055/view?picmode=&mode=tn&order=ordinal&start=1&count=20&dir=asc
> > >
> > > reference photo listed as "Driven ball-nut closeup"
> > > Chuck used a piece of 1"x2" approx. round stock, drilled for the ball-screw to pass through. He then drilled and tapped one end of the rod to 7/8 x 16 for the ball-nut to screw into. He bored the 42 tooth XL pulley on top to a 1" light press fit. Pressed the shaft and pulley together and used the set screw to hold it in place. Between the pulley and 1" collar on bottom are 1" ID needle roller bearings and washers.
> > > The assembly "pulley and rod" are slipped through the aluminum angle which has (brass bushing in the hole) bearing on both sides collar slipped over the other end and
> > > the ball-nut is used to preload the assembly then the 1" collar is tightened.
> > >
> > > Hope this make some.
> > >
> > > --- In CAD_CAM_EDM_DRO@yahoogroups.com, "jimmy_staton" <olecoot@> wrote:
> > > >
> > > > I have an old Shoptask 1720XMTC that I'm converting to CNC I have the X & Y axis
> > > > mostly done.
> > > >
> > > > At one time I saw a guy Ex. Boeing Machines (Chuck) maybe; he's on the Shoptask
> > > > site under projects, that had converted the Z axis to a ballscrew feed using 2 ballscrews to eliminate that horrible z axis setup feed. Would anyone have anymore information on how he did it.
> > > >
> > > > I realize I'm reaching but I've searched all over try to find more information on how it was done.
> > > >
> > > > Thanks
> > > > Jimmy
> > > >
> > >
> > >
> > >
> > >
> > > ------------------------------------
> > >
> > > Addresses:
> > > FAQ: http://www.ktmarketing.com/faq.html
> > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > >
> > > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@, timg@
> > > Moderator: pentam@ indigo_red@ davemucha@ [Moderators]
> > > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > >
> > > OFF Topic POSTS: General Machining
> > > If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
> > > http://www.metalworking.com/news_servers.html
> > >
> > > http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
> > >
> > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > > bill
> > > List Mom
> > > List Owner
> > >
> > > Yahoo! Groups Links
> > >
> > >
> > >
> > > This communication including any attachments, are intended
> > > for the exclusive use of the addressee(s) and contains
> > > confidential or copyrighted materials. Duplication,
> > > distribution or reproduction is strictly prohibited by law
> > > without written permission of Verrex
> > >
> >
> >
> >
> >
> > ------------------------------------
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> >
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@, timg@
> > Moderator: pentam@ indigo_red@ davemucha@ [Moderators]
> > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >
> > OFF Topic POSTS: General Machining
> > If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
> > http://www.metalworking.com/news_servers.html
> >
> > http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
> >
> > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > bill
> > List Mom
> > List Owner
> >
> > Yahoo! Groups Links
> >
> >
> >
> > This communication including any attachments, are intended
> > for the exclusive use of the addressee(s) and contains
> > confidential or copyrighted materials. Duplication,
> > distribution or reproduction is strictly prohibited by law
> > without written permission of Verrex
> >
>
>
>
>
> ------------------------------------
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
> Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
> Yahoo! Groups Links
>
>
>
> This communication including any attachments, are intended
> for the exclusive use of the addressee(s) and contains
> confidential or copyrighted materials. Duplication,
> distribution or reproduction is strictly prohibited by law
> without written permission of Verrex
>