Re: Ballscrews/linear drive
Posted by
Tony Jeffree
on 2001-01-18 00:44:25 UTC
At 08:18 18/01/01 +0000, you wrote:
slicer. No problem.
Regards,
Tony
>Try telling THAT to OSHA!That's easy - just re-describe it as a combination sliding door & meat
>
>
> >Emergency stop? This is for a Klingon ship bridge, if you are too slow
> >you don't -deserve- to survive!
> >
slicer. No problem.
Regards,
Tony
Discussion Thread
Steve Greenfield
2001-01-17 09:19:40 UTC
Ballscrews/linear drive
Tim Goldstein
2001-01-17 12:07:32 UTC
RE: [CAD_CAM_EDM_DRO] Ballscrews/linear drive
ballendo@y...
2001-01-17 12:41:05 UTC
re:Ballscrews/linear drive
ballendo@y...
2001-01-17 13:05:22 UTC
re:RE: Ballscrews/linear drive
Steve Greenfield
2001-01-17 14:32:04 UTC
Re: re:RE: Ballscrews/linear drive
dave engvall
2001-01-17 15:00:55 UTC
Re: [CAD_CAM_EDM_DRO] Ballscrews/linear drive
Smoke
2001-01-17 15:21:13 UTC
Re: [CAD_CAM_EDM_DRO] Ballscrews/linear drive
Tim Goldstein
2001-01-17 16:00:32 UTC
RE: [CAD_CAM_EDM_DRO] Ballscrews/linear drive
Steve Greenfield
2001-01-17 16:21:12 UTC
Re: re:Ballscrews/linear drive
Steve Greenfield
2001-01-17 16:26:40 UTC
Re: Ballscrews/linear drive
Steve Greenfield
2001-01-17 17:13:32 UTC
Re: Ballscrews/linear drive
Doug Harrison
2001-01-17 17:21:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: re:Ballscrews/linear drive
Smoke
2001-01-17 17:38:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ballscrews/linear drive
Rich D.
2001-01-17 17:43:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ballscrews/linear drive
Alan Marconett KM6VV
2001-01-17 18:02:03 UTC
RE: Ballscrews/linear drive
wanliker@a...
2001-01-17 18:06:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ballscrews/linear drive
Les Watts
2001-01-17 18:25:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: re:Ballscrews/linear drive
Ray
2001-01-17 19:31:35 UTC
Re: re:RE: Ballscrews/linear drive
Doug Harrison
2001-01-17 20:25:15 UTC
Re: [CAD_CAM_EDM_DRO] RE: Ballscrews/linear drive
Smoke
2001-01-17 20:58:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: re:Ballscrews/linear drive
Steve Greenfield
2001-01-17 21:11:09 UTC
Re: Ballscrews/linear drive
Steve Greenfield
2001-01-17 21:14:29 UTC
Re: Ballscrews/linear drive
Smoke
2001-01-17 21:25:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Ballscrews/linear drive
Tony Jeffree
2001-01-18 00:44:25 UTC
Re: Ballscrews/linear drive
ballendo@y...
2001-01-18 04:27:20 UTC
Re: Re: Ballscrews/linear drive
Carlos Guillermo
2001-01-18 04:49:52 UTC
Why ballscrews for linear drive?
Steve Greenfield
2001-01-18 08:53:44 UTC
Re: Ballscrews/linear drive
Steve Greenfield
2001-01-18 09:06:09 UTC
Re: Why ballscrews for linear drive?
Steve Greenfield
2001-01-18 09:14:27 UTC
Re: Why ballscrews for linear drive?
Sven Peter, TAD S.A.
2001-01-18 11:45:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: re:RE: Ballscrews/linear drive