CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works!

Posted by ptengin@a...
on 2001-02-23 23:52:40 UTC
In a message dated 2/22/01 7:17:31 PM Hawaiian Standard Time,
janders@... writes:

<< Doug,

A fairly tall cylinder with an inlet extending several inches down from
the top and an outlet at the very top shouldn't pick up much liquid,
especially if you place a baffle in front of the outlet to prevent any
possible direct splashes from hitting the outlet.

A 18" or so length of tubular drive shaft tubing would work.
You'd still really want some sort of filter between this and the pump.

Jon A.
>>


Doug,

You could use a 1 gallon Mayonaise jar if they still make them in glass.
I've seen the units doctors use for lipo suction. That is exactly what you
need.

Peter
THRD, Inc.

Discussion Thread

Jon Anderson 2001-02-21 20:32:07 UTC Vac table, it works! dougrasmussen@c... 2001-02-22 07:00:28 UTC Re: Vac table, it works! Smoke 2001-02-22 07:17:27 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! Jon Anderson 2001-02-22 07:23:42 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! Jon Elson 2001-02-22 12:37:40 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! Sven Peter, TAD S.A. 2001-02-22 14:19:09 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! ballendo@y... 2001-02-22 18:55:07 UTC vac pumps was Re: Vac table, it works! Jon Anderson 2001-02-22 19:29:50 UTC Re: [CAD_CAM_EDM_DRO] vac pumps was Re: Vac table, it works! ballendo@y... 2001-02-22 19:32:23 UTC vac pumps was Re: Vac table, it works! dougrasmussen@c... 2001-02-22 20:09:01 UTC Re: Vac table, it works! Jon Anderson 2001-02-22 21:15:41 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! Jon Elson 2001-02-22 22:20:45 UTC Re: [CAD_CAM_EDM_DRO] vac pumps was Re: Vac table, it works! Jon Elson 2001-02-22 22:26:05 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! dave engvall 2001-02-23 08:18:33 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! wanliker@a... 2001-02-23 09:34:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! Greg Nuspel 2001-02-23 09:50:48 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! Tim Goldstein 2001-02-23 10:02:31 UTC RE: [CAD_CAM_EDM_DRO] Re: Vac table, it works! Ricks 2001-02-23 20:55:55 UTC RE: [CAD_CAM_EDM_DRO] Re: Vac table, it works! wanliker@a... 2001-02-23 21:42:22 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! ptengin@a... 2001-02-23 23:52:40 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! Ricks 2001-02-24 20:48:28 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! Tim Goldstein 2001-02-24 21:35:09 UTC RE: [CAD_CAM_EDM_DRO] Re: Vac table, it works!