CAD CAM EDM DRO - Yahoo Group Archive

vac pumps was Re: Vac table, it works!

Posted by ballendo@y...
on 2001-02-22 19:32:23 UTC
Jon,

Good point. I did say "refrigeration" , NOT "refrigerator".

Ballendo


--- In CAD_CAM_EDM_DRO@y..., Jon Anderson <janders@n...> wrote:
> ballendo@y... wrote:
> >
> > Doug,
> >
> > You might try a regrigeration compressor!
>
> DO NOT dismantle a fridge for the compressor and haul the corpse to
the
> landfill/recycling. It's a $5,000 fine! If you must use one of
these,<snip>

Discussion Thread

Jon Anderson 2001-02-21 20:32:07 UTC Vac table, it works! dougrasmussen@c... 2001-02-22 07:00:28 UTC Re: Vac table, it works! Smoke 2001-02-22 07:17:27 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! Jon Anderson 2001-02-22 07:23:42 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! Jon Elson 2001-02-22 12:37:40 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! Sven Peter, TAD S.A. 2001-02-22 14:19:09 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! ballendo@y... 2001-02-22 18:55:07 UTC vac pumps was Re: Vac table, it works! Jon Anderson 2001-02-22 19:29:50 UTC Re: [CAD_CAM_EDM_DRO] vac pumps was Re: Vac table, it works! ballendo@y... 2001-02-22 19:32:23 UTC vac pumps was Re: Vac table, it works! dougrasmussen@c... 2001-02-22 20:09:01 UTC Re: Vac table, it works! Jon Anderson 2001-02-22 21:15:41 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! Jon Elson 2001-02-22 22:20:45 UTC Re: [CAD_CAM_EDM_DRO] vac pumps was Re: Vac table, it works! Jon Elson 2001-02-22 22:26:05 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! dave engvall 2001-02-23 08:18:33 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! wanliker@a... 2001-02-23 09:34:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! Greg Nuspel 2001-02-23 09:50:48 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! Tim Goldstein 2001-02-23 10:02:31 UTC RE: [CAD_CAM_EDM_DRO] Re: Vac table, it works! Ricks 2001-02-23 20:55:55 UTC RE: [CAD_CAM_EDM_DRO] Re: Vac table, it works! wanliker@a... 2001-02-23 21:42:22 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! ptengin@a... 2001-02-23 23:52:40 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! Ricks 2001-02-24 20:48:28 UTC Re: [CAD_CAM_EDM_DRO] Re: Vac table, it works! Tim Goldstein 2001-02-24 21:35:09 UTC RE: [CAD_CAM_EDM_DRO] Re: Vac table, it works!