CAD CAM EDM DRO - Yahoo Group Archive

Re: Smart/Dumb box again...

on 2001-02-28 13:19:24 UTC
Hi Brian,

Not at all! I think it's great that Linux is getting into the embedded
systems market! We were thinking about Qnix (sp?), as a possible
replacement. We'd like to get a real time operating system, although it
would mean total rewrite to take advantage of it. Royalty free would be
good, we currently license DataLight's DOS. We load drivers for Socket
Services and TFFS (m-sys), a driver for SRAM cards, (if present), and
hopefully ATA cards. (And This morning I found the reason the ATA card
was not "listening" to my commands!)

Thanks for the URL's, I'll check them out (then I'll HAVE to do
Linux!). My BIOS doesn't support int 13h (floppy/hard disk), we rely on
the PCMCIA. Would Linux be able to use the TFFS driver? Or a DOS-style
block memory device driver? Interesting.

Thanks for the info

Alan KM6VV


Brian Pitt wrote:
>
> HI Alan,
>
> I dont know if youre gona like the sound of this but Linux is
> making some moves in the embeded system market ;-)
> (complete control with no licencing fees )
> head over to
> http://www.linuxdevices.com and run a search on BIOS or
> Elan and you will find some stuff that may be usefull to ya
> Linux actualy never uses the BIOS once its loaded so a simple
> bootstrap loader will work
> there is also at least one realtime version of the linux kernel
> built for a 386sx and booting from a floppy
> ftp://ftp.rtlinux.com/pub/rtlinux/minirtl
> or http://rtlinux.org/minirtl.html
> and a couple of Linux-PLC type projects are in the works
> http://www.linuxplc.org
> http://www.freeio.org
>
> Brian
>
> On Tuesday 27 February 2001 23:59, you wrote:
> > Hi Brian,
> >
> > Yes! m-sys makes the disk-on-chip, interfaces like a EPROM. I have one
> > on a prototype board (at work) that's in the queue. Several new parts
> > on that board (job security)! Will need a new BIOS (board is a relative
> > to the hand held board I mentioned).
> >
> > I agree, work with what 'ya got! The 80 Mb PCMCIA card (ATA) works for
> > me! I am currently using a 33 mhz '386 as a target machine. Small disk
> > drive, etc.
> >
> > Work continues. Accurate timing is quite important; made easier by
> > having "complete control" of the box. Ideas?
> >
> > Alan KM6VV
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
> FAQ: http://www.ktmarketing.com/faq.html
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/

Discussion Thread

dkowalcz@i... 2001-02-26 16:15:10 UTC Smart/Dumb box again... Alan Marconett KM6VV 2001-02-26 17:07:50 UTC Re: Smart/Dumb box again... Carlos Guillermo 2001-02-26 17:52:42 UTC RE: [CAD_CAM_EDM_DRO] Smart/Dumb box again... Doug Harrison 2001-02-26 17:56:59 UTC Re: [CAD_CAM_EDM_DRO] Smart/Dumb box again... ballendo@y... 2001-02-26 18:11:06 UTC Re: Smart/Dumb box again... ballendo@y... 2001-02-26 18:15:38 UTC Re: Smart/Dumb box again... ballendo@y... 2001-02-26 18:22:16 UTC Re: Smart/Dumb box again... Alan Marconett KM6VV 2001-02-26 18:51:30 UTC Re: Smart/Dumb box again... Jon Elson 2001-02-26 22:36:06 UTC Re: [CAD_CAM_EDM_DRO] Smart/Dumb box again... Brian Walsh 2001-02-27 01:49:53 UTC Re: [CAD_CAM_EDM_DRO] Smart/Dumb box again... Ray 2001-02-27 06:56:01 UTC Re: Re: Smart/Dumb box again... Ray 2001-02-27 07:02:58 UTC Re: Re: Smart/Dumb box again... Jon Elson 2001-02-27 12:06:54 UTC Re: [CAD_CAM_EDM_DRO] Smart/Dumb box again... Paul 2001-02-27 12:48:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Smart/Dumb box again... Alan Marconett KM6VV 2001-02-27 14:56:27 UTC Re: Smart/Dumb box again... wanliker@a... 2001-02-27 16:52:05 UTC Re: [CAD_CAM_EDM_DRO] Re: Smart/Dumb box again... Brian Pitt 2001-02-27 23:05:10 UTC Re: [CAD_CAM_EDM_DRO] Re: Smart/Dumb box again... Tony Jeffree 2001-02-27 23:34:32 UTC Re: Smart/Dumb box again... Alan Marconett KM6VV 2001-02-28 00:01:08 UTC Re: Smart/Dumb box again... Alan Marconett KM6VV 2001-02-28 00:03:11 UTC Re: Smart/Dumb box again... Brian Pitt 2001-02-28 01:31:53 UTC Re: [CAD_CAM_EDM_DRO] Re: Smart/Dumb box again... Ian Wright 2001-02-28 01:53:10 UTC Re: [CAD_CAM_EDM_DRO] Re: Smart/Dumb box again... Jon Elson 2001-02-28 11:30:00 UTC Re: [CAD_CAM_EDM_DRO] Re: Smart/Dumb box again... dkowalcz@i... 2001-02-28 12:27:25 UTC Re: Smart/Dumb box again... (CPU timing) Paul 2001-02-28 12:34:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Smart/Dumb box again... Alan Marconett KM6VV 2001-02-28 13:19:24 UTC Re: Smart/Dumb box again... Alan Marconett KM6VV 2001-02-28 14:01:49 UTC Re: Smart/Dumb box again... Alan Marconett KM6VV 2001-02-28 14:22:17 UTC Re: Smart/Dumb box again... (CPU timing) Jon Elson 2001-02-28 16:09:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Smart/Dumb box again... Alan Marconett KM6VV 2001-02-28 17:01:00 UTC Re: Smart/Dumb box again... wanliker@a... 2001-02-28 17:36:33 UTC Re: [CAD_CAM_EDM_DRO] Re: Smart/Dumb box again... Henry H. Armstrong 2001-02-28 19:16:18 UTC Re: [CAD_CAM_EDM_DRO] Re: Smart/Dumb box again... Jon Elson 2001-02-28 23:26:29 UTC Re: [CAD_CAM_EDM_DRO] Re: Smart/Dumb box again... Matt Shaver 2001-02-28 23:42:56 UTC Re: [CAD_CAM_EDM_DRO] Re: Smart/Dumb box again... Jon Elson 2001-03-01 12:11:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Smart/Dumb box again... (CPU timing) Alan Marconett KM6VV 2001-03-01 12:16:26 UTC Re: Smart/Dumb box again... beer@s... 2001-03-02 08:41:47 UTC Re: Re: Smart/Dumb box again... (CPU timing)