CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available

Posted by Tim Goldstein
on 2001-03-30 11:34:05 UTC
My suggestion is if you like what it does step up to the full EMC. You will
get everything that is in the DOS/EMC and a multitasking graphical front end
along with the ability to network the system to other computers. Makes it
real easy to transfer those big files.

Same cost as DeskNCRT, free.

Tim
[Denver, CO]

> At 01:35 PM 3/30/2001 -0500, Rich D. wrote:
>
> >Is this a stand alone DOS program that I can d/l, install and run?
>
> It is a standalone G-code interpeter. I am using it currently on my
> CNCified Sherline mill.
>
> So far, it has worked flawlessly. Well, almost flawlessly. In
> interpreting the G-code it has run perfectly. In jog mode,
> there is a lack
> of filtering non-intended keypresses that sometimes have undesirable
> effects (like moving all three axes at once).
>
> I still need to do some experimenting and tweaking of the speed and
> acceleration parameters. The fastest I'm able to move the
> axes reliably is
> about 10 ipm. I'm using the Sherline motors and Dan Mauch's 2A driver
> board with a 24V, 8.3A switching power supply from Marlin P.
> Jones (with a
> 6800uf cap across the output).
>
> The best thing is that it is free, non-time-or-steps limited,
> can read in
> unlimited size G code files (my latest surfacing cut was
> running for about
> 4 hours) and lets me be running while I decide whether it
> would be worth
> buying CNCPro or another commercial software.
>
> Best regards,
>
> Randy
>
> Randy Gordon-Gilmore ,----.___________ ______________
> _________________
> ProtoTrains // = = === == || == == == = || ==
> == == = == =|
> Rio Vista, CA, USA
> /-O==O------------o==o------------o==o-----------o==o-'
> zephyrus@...
http://www.rickadee.net/~zephyrus


FAQ: http://www.ktmarketing.com/faq.html

Discussion Thread

Rich D. 2001-03-30 10:34:35 UTC Re: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available Randy Gordon-Gilmore 2001-03-30 11:20:09 UTC Re: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available Tim Goldstein 2001-03-30 11:34:05 UTC RE: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available Randy Gordon-Gilmore 2001-03-30 12:00:12 UTC RE: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available Tim Goldstein 2001-03-30 12:14:22 UTC RE: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available cadman@p... 2001-03-30 13:02:12 UTC Re: DOS/EMC aka DeskNCrt now freely available Paul 2001-03-30 13:08:59 UTC RE: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available Randy Gordon-Gilmore 2001-03-30 13:32:34 UTC RE: DeskNCrt Ian Wright 2001-03-30 13:47:11 UTC Re: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available Ian Wright 2001-03-30 13:50:03 UTC Re: [CAD_CAM_EDM_DRO] Re: DOS/EMC aka DeskNCrt now freely available Tim Goldstein 2001-03-30 14:04:06 UTC RE: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available Paul 2001-03-30 15:07:15 UTC Re: [CAD_CAM_EDM_DRO] Re: DOS/EMC aka DeskNCrt now freely available Jon Elson 2001-03-30 16:05:04 UTC Re: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available Jon Elson 2001-03-30 16:11:21 UTC Re: [CAD_CAM_EDM_DRO] Re: DOS/EMC aka DeskNCrt now freely available Ray 2001-03-30 18:28:08 UTC Re: RE: DOS/EMC aka DeskNCrt now freely available Mike Gann 2001-03-30 22:22:38 UTC Re: [CAD_CAM_EDM_DRO] Re: RE: DOS/EMC aka DeskNCrt now freely available Robert Allen & Marsha Camp 2001-03-31 04:19:48 UTC Re: [CAD_CAM_EDM_DRO] RE: DOS/EMC aka DeskNCrt now freely available Tim Goldstein 2001-03-31 10:05:37 UTC RE: [CAD_CAM_EDM_DRO] RE: DOS/EMC aka DeskNCrt now freely available Alan Marconett KM6VV 2001-03-31 12:27:58 UTC Re: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available Tim Goldstein 2001-03-31 13:05:37 UTC RE: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available Paul 2001-03-31 13:49:37 UTC RE: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available Alan Marconett KM6VV 2001-03-31 14:12:49 UTC RE: DOS/EMC aka DeskNCrt now freely available Jon Elson 2001-03-31 21:15:20 UTC Re: [CAD_CAM_EDM_DRO] Re: DOS/EMC aka DeskNCrt now freely available dave engvall 2001-04-01 08:36:58 UTC Re: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available Alan Marconett KM6VV 2001-04-01 14:22:18 UTC Re: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available Jon Elson 2001-04-01 23:43:56 UTC Re: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available Ian Wright 2001-04-02 01:27:39 UTC Re: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available Tim Goldstein 2001-04-02 09:01:22 UTC RE: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available Alan Marconett KM6VV 2001-04-02 11:51:11 UTC Re: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available Alan Marconett KM6VV 2001-04-02 11:57:53 UTC Re: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available Jon Elson 2001-04-02 12:32:32 UTC Re: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available Jon Elson 2001-04-02 14:02:48 UTC Re: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available Alan Marconett KM6VV 2001-04-02 17:12:06 UTC Re: [CAD_CAM_EDM_DRO] DOS/EMC aka DeskNCrt now freely available dave engvall 2001-04-04 20:46:33 UTC Re: [CAD_CAM_EDM_DRO] Re: RE: DOS/EMC aka DeskNCrt now freely available Ray 2001-04-05 09:39:06 UTC Re: Re: RE: DOS/EMC aka DeskNCrt now freely available Tim Goldstein 2001-04-05 10:29:21 UTC RE: [CAD_CAM_EDM_DRO] Re: Re: RE: DOS/EMC aka DeskNCrt now freely available