CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Re: Climb Milling (again)

Posted by Tim Goldstein
on 2001-06-05 19:50:35 UTC
Opinion vs practical application:
My Shoptask is using single nutted ball screws I made from the McMaster Carr
5/8" stock. It has about .005" backlash on both axis's. Running with
backlash compensation noticeably improves the ability to hold tolerance on
the parts.

All the opinions in the world will not change this demonstratable fact.

OTOH, if I was doing it again I would put on double nuts and preload them
for zero backlash.

Tim
[Denver, CO]

> -----Original Message-----
>
> I've been looking at some of these responses for "software
> compensation for
> backlash".
> Real HOGWASH IMO. If the machine "jumps" due to excessive load under
> backlash, ho the H is the software going to know how much "jump" to
> compensate for? Furthermore, how's the software going to know how much
> backlash you have in your machine...or how much extra backlash to
> compenste
> for due to wear or poor machine adjustment?
>
> Smoke
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/

Discussion Thread

ron ginger 2001-06-04 15:35:10 UTC Re: Climb Milling ballendo@y... 2001-06-04 17:57:33 UTC Re: Climb Milling dougrasmussen@c... 2001-06-04 20:28:45 UTC Re: Climb Milling Jon Elson 2001-06-04 21:59:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Climb Milling yahoo@a... 2001-06-05 05:32:00 UTC Re: Climb Milling Alan Marconett KM6VV 2001-06-05 10:58:00 UTC Re: [CAD_CAM_EDM_DRO] Re: Climb Milling Jon Elson 2001-06-05 11:30:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Climb Milling Hugh Currin 2001-06-05 12:30:11 UTC Re: Climb Milling Rich D. 2001-06-05 12:38:26 UTC Re: [CAD_CAM_EDM_DRO] Re: Climb Milling Fred Smith 2001-06-05 15:14:44 UTC Re: Climb Milling RC 2001-06-05 15:35:17 UTC Re: [CAD_CAM_EDM_DRO] Re: Climb Milling dave engvall 2001-06-05 16:13:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Climb Milling dave engvall 2001-06-05 16:16:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Climb Milling ballendo@y... 2001-06-05 18:57:23 UTC Re: Climb Milling (again) Smoke 2001-06-05 19:22:34 UTC Re: [CAD_CAM_EDM_DRO] Re: Climb Milling (again) Sven Peter, TAD S.A. 2001-06-05 19:29:40 UTC Re: [CAD_CAM_EDM_DRO] Re: Climb Milling yahoo@a... 2001-06-05 19:46:12 UTC Re: Climb Milling Tim Goldstein 2001-06-05 19:50:35 UTC RE: [CAD_CAM_EDM_DRO] Re: Climb Milling (again) dougrasmussen@c... 2001-06-05 19:53:22 UTC Re: Climb Milling (again) ballendo@y... 2001-06-05 20:10:17 UTC Re: Climb Milling (again) ballendo@y... 2001-06-05 20:26:41 UTC Re: Climb Milling ballendo@y... 2001-06-05 20:29:03 UTC Re: Climb Milling (again) ballendo@y... 2001-06-05 20:33:01 UTC re:backlash comp was Re: Climb Milling (again) Chris Stratton 2001-06-06 04:48:36 UTC Re: [CAD_CAM_EDM_DRO] re:backlash comp was Re: Climb Milling (again) ballendo@y... 2001-06-06 05:25:57 UTC Re: Climb Milling yahoo@a... 2001-06-06 05:32:56 UTC re:backlash comp was Re: Climb Milling (again) ballendo@y... 2001-06-06 06:18:16 UTC re:backlash comp was Re: Climb Milling (again) Smoke 2001-06-06 12:05:16 UTC Re: [CAD_CAM_EDM_DRO] Re: Climb Milling (again) Smoke 2001-06-06 12:05:38 UTC Re: [CAD_CAM_EDM_DRO] re:backlash comp was Re: Climb Milling (again)