CAD CAM EDM DRO - Yahoo Group Archive

Re: Climb Milling

Posted by yahoo@a...
on 2001-06-05 05:32:00 UTC
You don't implement backlash compensation by "backing the motor".
Backlash compensation works because each time that the direction is
reversed, the software realizes that turns-of-the-motor will not be
reflected in the displacement. Therefore the software runs the motor
a compensated amount more than would otherwise be required.

This will not effect the milling direction or interfere with climb
milling.

Buck

--- In CAD_CAM_EDM_DRO@y..., ron ginger <ronginger@r...> wrote:
> After all the good explanations and horror stories of the results of
> climb miling and backlash lets hear from the guys that think
software
> compensation for backlash is a good, or even useable thing!
>
> Sure, the program can cause the motor to backup to the right
> mathematical spot, but while its doing that compensation the table
is
> quite free to get grabbed by the tool.
>
> A great bit of proof why Ive always maintained software compensaton
for
> backlash is bogus.
>
> ron ginger

Discussion Thread

ron ginger 2001-06-04 15:35:10 UTC Re: Climb Milling ballendo@y... 2001-06-04 17:57:33 UTC Re: Climb Milling dougrasmussen@c... 2001-06-04 20:28:45 UTC Re: Climb Milling Jon Elson 2001-06-04 21:59:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Climb Milling yahoo@a... 2001-06-05 05:32:00 UTC Re: Climb Milling Alan Marconett KM6VV 2001-06-05 10:58:00 UTC Re: [CAD_CAM_EDM_DRO] Re: Climb Milling Jon Elson 2001-06-05 11:30:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Climb Milling Hugh Currin 2001-06-05 12:30:11 UTC Re: Climb Milling Rich D. 2001-06-05 12:38:26 UTC Re: [CAD_CAM_EDM_DRO] Re: Climb Milling Fred Smith 2001-06-05 15:14:44 UTC Re: Climb Milling RC 2001-06-05 15:35:17 UTC Re: [CAD_CAM_EDM_DRO] Re: Climb Milling dave engvall 2001-06-05 16:13:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Climb Milling dave engvall 2001-06-05 16:16:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Climb Milling ballendo@y... 2001-06-05 18:57:23 UTC Re: Climb Milling (again) Smoke 2001-06-05 19:22:34 UTC Re: [CAD_CAM_EDM_DRO] Re: Climb Milling (again) Sven Peter, TAD S.A. 2001-06-05 19:29:40 UTC Re: [CAD_CAM_EDM_DRO] Re: Climb Milling yahoo@a... 2001-06-05 19:46:12 UTC Re: Climb Milling Tim Goldstein 2001-06-05 19:50:35 UTC RE: [CAD_CAM_EDM_DRO] Re: Climb Milling (again) dougrasmussen@c... 2001-06-05 19:53:22 UTC Re: Climb Milling (again) ballendo@y... 2001-06-05 20:10:17 UTC Re: Climb Milling (again) ballendo@y... 2001-06-05 20:26:41 UTC Re: Climb Milling ballendo@y... 2001-06-05 20:29:03 UTC Re: Climb Milling (again) ballendo@y... 2001-06-05 20:33:01 UTC re:backlash comp was Re: Climb Milling (again) Chris Stratton 2001-06-06 04:48:36 UTC Re: [CAD_CAM_EDM_DRO] re:backlash comp was Re: Climb Milling (again) ballendo@y... 2001-06-06 05:25:57 UTC Re: Climb Milling yahoo@a... 2001-06-06 05:32:56 UTC re:backlash comp was Re: Climb Milling (again) ballendo@y... 2001-06-06 06:18:16 UTC re:backlash comp was Re: Climb Milling (again) Smoke 2001-06-06 12:05:16 UTC Re: [CAD_CAM_EDM_DRO] Re: Climb Milling (again) Smoke 2001-06-06 12:05:38 UTC Re: [CAD_CAM_EDM_DRO] re:backlash comp was Re: Climb Milling (again)