Re: [CAD_CAM_EDM_DRO] Re: Cadcam, CNC & eCommerce
Posted by
Sven Peter, TAD S.A.
on 2001-06-24 17:01:57 UTC
Hello I had to rescrape a old lathe once where on 1,8m
close to the chuck the bed itsself was worn 0,47mm (o,o19")
It took me 354 hours. If you call that low budget then have fun.
Enjoy your blisters and backache.
Better to give it out or away to a foundry.
Sven Peter
hllrsr@... wrote:
close to the chuck the bed itsself was worn 0,47mm (o,o19")
It took me 354 hours. If you call that low budget then have fun.
Enjoy your blisters and backache.
Better to give it out or away to a foundry.
Sven Peter
hllrsr@... wrote:
> Wally,[Non-text portions of this message have been removed]
> Found out about UPS the hard way when I ordered some cogged timing belts
> for a belt reduction drive, $25 CAN for the belts, $15 CAN for the
> shipping, $45 CAN FOR THE UPS BROKERAGE! Now I let Canadian Bearings
> deal with the headache. <gr>
>
> Any ideas out there, on an economical way to build up & true a lathe
> bed?
> Have a chance at a Colchester Student that has been partially
> retro-fitted, but in the 8" closest to the chuck it tapers .037" due to
> wear.
> I can send it out to be ground and get the gibs built up, but the whole
> project is a self imposed challenge to see how low cost I can go.
> BTW, the lathe is likely to cost ~$500 CAN with an old Fanuc controller
> boxed and included.
>
> Iain
> Oro Station, Ont.
> (approx. 60 min. N. of Toronto)
>
> > --Snip--
> >
> > I prefer USPS also for most of the things I buy from the US, which are
> > mostly old books on Numerical Control. I wonder
> > how many other Canucks are on the list ?
> >
> > -Wally
> >
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
Discussion Thread
cadcamcenter@y...
2001-06-19 05:13:02 UTC
Cadcam, CNC & eCommerce
cncdxf@a...
2001-06-19 15:10:59 UTC
Re: Cadcam, CNC & eCommerce
Tim Goldstein
2001-06-19 15:56:30 UTC
RE: [CAD_CAM_EDM_DRO] Re: Cadcam, CNC & eCommerce
Jon Elson
2001-06-19 17:38:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Cadcam, CNC & eCommerce
Henry H. Armstrong
2001-06-19 20:24:17 UTC
Re: [CAD_CAM_EDM_DRO] Cadcam, CNC & eCommerce
cadcamcenter@y...
2001-06-19 21:10:02 UTC
Cadcam, CNC & eCommerce
Jon Anderson
2001-06-19 22:14:36 UTC
Re: [CAD_CAM_EDM_DRO] Cadcam, CNC & eCommerce
wanliker@a...
2001-06-19 22:44:48 UTC
Re: [CAD_CAM_EDM_DRO] Cadcam, CNC & eCommerce
cadcamcenter@y...
2001-06-20 02:32:41 UTC
Re: Cadcam, CNC & eCommerce
Jon Elson
2001-06-20 09:59:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Cadcam, CNC & eCommerce
Al Schoepp
2001-06-20 11:14:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Cadcam, CNC & eCommerce
cadcamcenter@y...
2001-06-20 11:35:43 UTC
Re: Cadcam, CNC & eCommerce
brian
2001-06-20 15:11:09 UTC
Re: [CAD_CAM_EDM_DRO] Cadcam, CNC & eCommerce
Wally Daniels
2001-06-20 18:57:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: Cadcam, CNC & eCommerce
Peter Chen
2001-06-20 21:21:25 UTC
Cadcam, CNC & eCommerce
Al Schoepp
2001-06-22 06:16:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Cadcam, CNC & eCommerce
Ward M.
2001-06-24 00:21:28 UTC
RE: [CAD_CAM_EDM_DRO] Cadcam, CNC & eCommerce
Wally Daniels
2001-06-24 15:42:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Cadcam, CNC & eCommerce
hllrsr@c...
2001-06-24 16:04:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Cadcam, CNC & eCommerce
Sven Peter, TAD S.A.
2001-06-24 17:01:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Cadcam, CNC & eCommerce
ballendo@y...
2001-06-26 05:01:38 UTC
Re: Cadcam, CNC & eCommerce
Al Schoepp
2001-06-26 07:27:28 UTC
Re: [CAD_CAM_EDM_DRO] books
wdaniels@g...
2001-06-26 08:30:47 UTC
Re: [CAD_CAM_EDM_DRO] books
Al Schoepp
2001-06-27 06:55:50 UTC
Re: [CAD_CAM_EDM_DRO] books
Sven Peter, TAD S.A.
2001-06-27 21:53:35 UTC
Re: [CAD_CAM_EDM_DRO] books
Hugh & Denise Currin
2001-07-03 11:40:46 UTC
Axis Re-set ?
Tim Goldstein
2001-07-03 11:57:44 UTC
RE: [CAD_CAM_EDM_DRO] Axis Re-set ?
Ian Wright
2001-07-03 14:31:14 UTC
Re: [CAD_CAM_EDM_DRO] Axis Re-set ?
Jon Elson
2001-07-03 22:24:11 UTC
Re: [CAD_CAM_EDM_DRO] Axis Re-set ?
Jon Elson
2001-07-03 22:30:04 UTC
Re: [CAD_CAM_EDM_DRO] Axis Re-set ?
Ian Wright
2001-07-04 02:03:56 UTC
Re: [CAD_CAM_EDM_DRO] Axis Re-set ?
Ian Wright
2001-07-04 12:38:59 UTC
Re: [CAD_CAM_EDM_DRO] Axis Re-set ?
Jon Elson
2001-07-04 15:59:13 UTC
Re: [CAD_CAM_EDM_DRO] Axis Re-set ?
mkcchrn
2007-11-24 10:21:36 UTC
books