CAD CAM EDM DRO - Yahoo Group Archive

Re: Flat Holes

Posted by Fred Smith
on 2001-11-10 10:29:44 UTC
--- In CAD_CAM_EDM_DRO@y..., gm4ta@i... wrote:
> Thanks everyone for their reply! I can't believe how much I'm
> learning from this group. At first I thought that there is no way
of
> making my guitar bridge. But now as I gain more knowledge on tools
> it's becoming much more possible. The next thing I'm going to buy
> when I go to Home Depot will be an 2 end mills: one for the 6-32
> socket head cap and one for the 4-40.

Of course if you are really trying to save money, you might just
counter drill the head clearance hole and not worry if there is a
flat under the head of your Socket head screws. In soft material as
you tighten the screw, it will bite into the angle left by the drill
tip. With those small sizes you are probably overdesigning your
fasteners, so the contact under the screw head probably does not
matter.

Best Regards,

Fred Smith
IMService

Discussion Thread

gm4ta@i... 2001-11-09 14:23:35 UTC Flat Holes ccs@m... 2001-11-09 14:31:39 UTC Re: [CAD_CAM_EDM_DRO] Flat Holes Carey L. Culpepper 2001-11-09 14:34:24 UTC Re: [CAD_CAM_EDM_DRO] Flat Holes Smoke 2001-11-09 15:22:44 UTC Re: [CAD_CAM_EDM_DRO] Flat Holes Alan Marconett KM6VV 2001-11-09 17:00:44 UTC Re: [CAD_CAM_EDM_DRO] Flat Holes heemanshu B Shah 2001-11-09 17:30:23 UTC Re: [CAD_CAM_EDM_DRO] Flat Holes gm4ta@i... 2001-11-09 18:53:46 UTC Re: Flat Holes ccs@m... 2001-11-09 19:15:04 UTC Re: [CAD_CAM_EDM_DRO] Re: Flat Holes Marcus & Eva 2001-11-09 20:10:11 UTC Re: [CAD_CAM_EDM_DRO] Re: Flat Holes Jon Elson 2001-11-09 22:16:38 UTC Re: [CAD_CAM_EDM_DRO] Flat Holes Rick Miller 2001-11-09 22:26:33 UTC Re: [CAD_CAM_EDM_DRO] Flat Holes Smoke 2001-11-09 22:31:11 UTC Re: [CAD_CAM_EDM_DRO] Re: Flat Holes ppump11578@a... 2001-11-10 04:12:28 UTC Re: [CAD_CAM_EDM_DRO] Flat Holes Fred Smith 2001-11-10 10:29:44 UTC Re: Flat Holes Chris L 2001-11-10 11:03:01 UTC Re: [CAD_CAM_EDM_DRO] Re: Flat Holes dougrasmussen@c... 2001-11-10 17:15:20 UTC Re: Flat Holes gm4ta@i... 2001-11-10 18:41:55 UTC Re: Flat Holes Marcus & Eva 2001-11-10 19:20:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Flat Holes Jon Elson 2001-11-10 20:42:42 UTC Re: [CAD_CAM_EDM_DRO] Re: Flat Holes Smoke 2001-11-11 07:48:12 UTC Re: [CAD_CAM_EDM_DRO] Re: Flat Holes Smoke 2001-11-11 07:51:43 UTC Re: [CAD_CAM_EDM_DRO] Re: Flat Holes johnhe 2001-11-11 08:25:24 UTC Re: [CAD_CAM_EDM_DRO] Re: Flat Holes Smoke 2001-11-11 18:29:57 UTC Re: [CAD_CAM_EDM_DRO] Re: Flat Holes ballendo@y... 2001-11-12 00:06:10 UTC Re: Flat Holes ballendo@y... 2001-11-12 01:53:02 UTC Re: Flat Holes