Re: OK, I've got a detent encoder... What now?
Posted by
imserv1
on 2002-02-16 21:43:46 UTC
--- In CAD_CAM_EDM_DRO@y..., Spehro Pefhany <speff@i...> wrote:
be 10 or 20 or 50 or 100 detents. One full revolution is important
and 18 does not convert to any useful scaled units. Is this a $20
part or a $100 part? Is it available in one of the listed scalable
numbers?
Best Regards,
Fred Smith
IMService
> At 06:59 PM 2/16/02 +0000, you wrote:Spehro, this is just about right for the application, except, it MUST
> We use a bunch of mechanical encoders in our production. Want to use
> that for an example? 18 steps/revolution and a push-switch in the
> shaft. Two quadrature outputs, one double change per detent.
> Not expensive. Bounce < 5msec, phase difference at 1 rotation/sec
> > 4msec initial, >2.5 msec at end of life. At each detent A
> is guaranteed "off", B is undefined.
>
> http://www.speff.com/trexon_encoder.gif (also 20mm L1 available)
be 10 or 20 or 50 or 100 detents. One full revolution is important
and 18 does not convert to any useful scaled units. Is this a $20
part or a $100 part? Is it available in one of the listed scalable
numbers?
Best Regards,
Fred Smith
IMService
Discussion Thread
vrsculptor
2002-02-16 10:59:21 UTC
OK, I've got a detent encoder... What now?
imserv1
2002-02-16 11:20:40 UTC
Re: OK, I've got a detent encoder... What now?
Brian Pitt
2002-02-16 12:01:43 UTC
Re: [CAD_CAM_EDM_DRO] OK, I've got a detent encoder... What now?
Spehro Pefhany
2002-02-16 12:25:14 UTC
Re: [CAD_CAM_EDM_DRO] OK, I've got a detent encoder... What now?
imserv1
2002-02-16 21:43:46 UTC
Re: OK, I've got a detent encoder... What now?
Marcus & Eva
2002-02-17 09:08:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: OK, I've got a detent encoder... What now?
Spehro Pefhany
2002-02-17 09:17:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: OK, I've got a detent encoder... What now?
imserv1
2002-02-17 12:38:55 UTC
Re: OK, I've got a detent encoder... What now?
Alan Marconett KM6VV
2002-02-17 13:13:31 UTC
Re: OK, I've got a detent encoder... What now?
Raymond Heckert
2002-02-17 15:37:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: OK, I've got a detent encoder... What now?
audiomaker2000
2002-02-17 15:51:02 UTC
Re: OK, I've got a detent encoder... Hello?
Randy Gordon-Gilmore
2002-02-17 21:40:01 UTC
Honing TiN inserts? And triangular insert question...
Marcus & Eva
2002-02-17 22:40:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: OK, I've got a detent encoder... Hello?
ballendo
2002-02-17 23:41:34 UTC
Re: OK, I've got a detent encoder... What now?
audiomaker2000
2002-02-18 00:47:24 UTC
Re: OK, I've got a detent encoder... Hello?
ballendo
2002-02-18 01:36:07 UTC
Re: OK, I've got a detent encoder... Hello?
audiomaker2000
2002-02-18 01:43:37 UTC
Re: OK, I've got a detent encoder... Hello?
ballendo
2002-02-18 03:15:07 UTC
What's it for? was Re: OK, I've got a detent encoder... Hello?
Marcus & Eva
2002-02-18 08:22:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: OK, I've got a detent encoder... What now?
audiomaker2000
2002-02-18 08:39:25 UTC
What's it for? was Re: OK, I've got a detent encoder... Hello?
Brian Pitt
2002-02-18 12:43:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: OK, I've got a detent encoder... What now?
ballendo
2002-02-18 21:03:13 UTC
Clicks are clicks... was Re: OK, I've got a detent encoder... What now?
ballendo
2002-02-18 21:29:43 UTC
What's it for? was Re: OK, I've got a detent encoder... Hello?
William Scalione
2002-02-19 07:44:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: OK, I've got a detent encoder... What now?
audiomaker2000
2002-02-19 08:25:51 UTC
Re: OK, I've got a detent encoder... What now?
Alan Marconett KM6VV
2002-02-19 11:52:44 UTC
Re: OK, I've got a detent encoder... What now?
William Scalione
2002-02-19 16:50:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: OK, I've got a detent encoder... What now?
imserv1
2002-02-19 17:02:09 UTC
Re: OK, I've got a detent encoder... What now?
Brian Pitt
2002-02-19 18:38:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: OK, I've got a detent encoder... What now?
Alan Marconett KM6VV
2002-02-19 23:03:49 UTC
Re: OK, I've got a detent encoder... What now?
tedinoue
2002-02-20 03:16:15 UTC
Re: OK, I've got a detent encoder... What now?