Re: [CAD_CAM_EDM_DRO] Re: OK, I've got a detent encoder... What now?
Posted by
Raymond Heckert
on 2002-02-17 15:37:38 UTC
Was I was you, I'd use an edge-finder! They tolerate up to .050 of "oops,
too much" movement. I can get an edge finder to "repeat" within about
0.0002".
I'd really worry about bending something by jumpin' at it .01" at a time,
by the eyeball.
RayHex
----------
too much" movement. I can get an edge finder to "repeat" within about
0.0002".
I'd really worry about bending something by jumpin' at it .01" at a time,
by the eyeball.
RayHex
----------
> From: Marcus & Eva <implmex@...>click
> When I am jogging up to the edge of a job, I eyeball it at 0.01" per
> until I'm close to my gauge block size (I use a 3/4" dia pin in thecollet,
> and a 0.125 gauge block as a feeler gauge for setting up).push
> Then I switch to 0.0001" per click and run the pin up until I can just
> the gauge block into the gap.as
> For this operation I don't care a hoot what the graduations are, so long
> I have a coarse one for rough positioning, and a fine one for twiddlingin
> the last tenths.
Discussion Thread
vrsculptor
2002-02-16 10:59:21 UTC
OK, I've got a detent encoder... What now?
imserv1
2002-02-16 11:20:40 UTC
Re: OK, I've got a detent encoder... What now?
Brian Pitt
2002-02-16 12:01:43 UTC
Re: [CAD_CAM_EDM_DRO] OK, I've got a detent encoder... What now?
Spehro Pefhany
2002-02-16 12:25:14 UTC
Re: [CAD_CAM_EDM_DRO] OK, I've got a detent encoder... What now?
imserv1
2002-02-16 21:43:46 UTC
Re: OK, I've got a detent encoder... What now?
Marcus & Eva
2002-02-17 09:08:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: OK, I've got a detent encoder... What now?
Spehro Pefhany
2002-02-17 09:17:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: OK, I've got a detent encoder... What now?
imserv1
2002-02-17 12:38:55 UTC
Re: OK, I've got a detent encoder... What now?
Alan Marconett KM6VV
2002-02-17 13:13:31 UTC
Re: OK, I've got a detent encoder... What now?
Raymond Heckert
2002-02-17 15:37:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: OK, I've got a detent encoder... What now?
audiomaker2000
2002-02-17 15:51:02 UTC
Re: OK, I've got a detent encoder... Hello?
Randy Gordon-Gilmore
2002-02-17 21:40:01 UTC
Honing TiN inserts? And triangular insert question...
Marcus & Eva
2002-02-17 22:40:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: OK, I've got a detent encoder... Hello?
ballendo
2002-02-17 23:41:34 UTC
Re: OK, I've got a detent encoder... What now?
audiomaker2000
2002-02-18 00:47:24 UTC
Re: OK, I've got a detent encoder... Hello?
ballendo
2002-02-18 01:36:07 UTC
Re: OK, I've got a detent encoder... Hello?
audiomaker2000
2002-02-18 01:43:37 UTC
Re: OK, I've got a detent encoder... Hello?
ballendo
2002-02-18 03:15:07 UTC
What's it for? was Re: OK, I've got a detent encoder... Hello?
Marcus & Eva
2002-02-18 08:22:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: OK, I've got a detent encoder... What now?
audiomaker2000
2002-02-18 08:39:25 UTC
What's it for? was Re: OK, I've got a detent encoder... Hello?
Brian Pitt
2002-02-18 12:43:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: OK, I've got a detent encoder... What now?
ballendo
2002-02-18 21:03:13 UTC
Clicks are clicks... was Re: OK, I've got a detent encoder... What now?
ballendo
2002-02-18 21:29:43 UTC
What's it for? was Re: OK, I've got a detent encoder... Hello?
William Scalione
2002-02-19 07:44:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: OK, I've got a detent encoder... What now?
audiomaker2000
2002-02-19 08:25:51 UTC
Re: OK, I've got a detent encoder... What now?
Alan Marconett KM6VV
2002-02-19 11:52:44 UTC
Re: OK, I've got a detent encoder... What now?
William Scalione
2002-02-19 16:50:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: OK, I've got a detent encoder... What now?
imserv1
2002-02-19 17:02:09 UTC
Re: OK, I've got a detent encoder... What now?
Brian Pitt
2002-02-19 18:38:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: OK, I've got a detent encoder... What now?
Alan Marconett KM6VV
2002-02-19 23:03:49 UTC
Re: OK, I've got a detent encoder... What now?
tedinoue
2002-02-20 03:16:15 UTC
Re: OK, I've got a detent encoder... What now?