Re: [CAD_CAM_EDM_DRO] Auto tool changers
Posted by
wanliker@a...
on 2002-02-22 15:26:11 UTC
EMCO COMPACT 5 LATHE TURRET
The lathe tools are held in place with set screws (2), from the bottom of the
slots. The hole type of tool holders on the points have bushings bored to
fit the tool, and set screw (1) going thru the bushing sides to hold the tool
and bushing in place.
The ends of the triangle shaped turret are rounded off, the height from the
flat to the radius at the top is about 4 3/16 of an inch. By the way, the
turret is mounted vertically.
The tool rotates up past the ratchet, and then reverses to the ratchet stop
to be in cutting position. The DC motor is always applying a reduced torque
to hold it in this position when cutting.
This is a small machine 5 x 12 lathe, it does have reverse, but not sure the
turret would hold in position when cutting in reverse.
Remember as the tool rotates up the ratchet releases, when it gets to the
next position it goes far enough for the next ratchet position, then the
turret reverses, and goes backwards (down) and locks up the ratchet. The
reduced motor torque holds the turret against the stop, for cutting.
Directions of movement are at the lathe centerline.
bill
The lathe tools are held in place with set screws (2), from the bottom of the
slots. The hole type of tool holders on the points have bushings bored to
fit the tool, and set screw (1) going thru the bushing sides to hold the tool
and bushing in place.
The ends of the triangle shaped turret are rounded off, the height from the
flat to the radius at the top is about 4 3/16 of an inch. By the way, the
turret is mounted vertically.
The tool rotates up past the ratchet, and then reverses to the ratchet stop
to be in cutting position. The DC motor is always applying a reduced torque
to hold it in this position when cutting.
This is a small machine 5 x 12 lathe, it does have reverse, but not sure the
turret would hold in position when cutting in reverse.
Remember as the tool rotates up the ratchet releases, when it gets to the
next position it goes far enough for the next ratchet position, then the
turret reverses, and goes backwards (down) and locks up the ratchet. The
reduced motor torque holds the turret against the stop, for cutting.
Directions of movement are at the lathe centerline.
bill
> That's what I want to know as well. And also, what holds the tool in place?[Non-text portions of this message have been removed]
> I mean, why doesn't it wander towards the next ratchet when force is put on
> the tool? Is it because the force on the tool in CCW is pushing down and
> trying to force the stop over a wall? If that's so then this sort of
> changer
> wouldn't work in CW would it?
>
Discussion Thread
John H.
2002-02-21 22:08:45 UTC
Auto tool changers
audiomaker2000
2002-02-22 03:33:21 UTC
Re: Auto tool changers
David M. Munro
2002-02-22 04:14:12 UTC
Re: [CAD_CAM_EDM_DRO] Auto tool changers
dave_ace_me
2002-02-22 04:25:26 UTC
Re: Auto tool changers
Smoke
2002-02-22 06:14:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers
wanliker@a...
2002-02-22 07:05:58 UTC
Re: [CAD_CAM_EDM_DRO] Auto tool changers
Marcus & Eva
2002-02-22 07:24:41 UTC
Re: [CAD_CAM_EDM_DRO] Auto tool changers
ballendo
2002-02-22 08:03:12 UTC
Re: Auto tool changers
Drew Rogge
2002-02-22 08:16:15 UTC
Re: [CAD_CAM_EDM_DRO] Auto tool changers
Alan Marconett KM6VV
2002-02-22 11:41:34 UTC
Re: [CAD_CAM_EDM_DRO] Auto tool changers
Drew Rogge
2002-02-22 11:49:37 UTC
Re: [CAD_CAM_EDM_DRO] Auto tool changers
Alan Marconett KM6VV
2002-02-22 13:07:10 UTC
Re: [CAD_CAM_EDM_DRO] Auto tool changers
John H.
2002-02-22 13:13:40 UTC
Re: [CAD_CAM_EDM_DRO] Auto tool changers
wanliker@a...
2002-02-22 14:09:18 UTC
Re: [CAD_CAM_EDM_DRO] Auto tool changers
wanliker@a...
2002-02-22 14:11:08 UTC
Re: [CAD_CAM_EDM_DRO] Auto tool changers
wanliker@a...
2002-02-22 14:59:20 UTC
Re: [CAD_CAM_EDM_DRO] Auto tool changers
wanliker@a...
2002-02-22 15:26:11 UTC
Re: [CAD_CAM_EDM_DRO] Auto tool changers
Chris Clough
2002-02-22 15:30:12 UTC
PLC Programming - anyone?
Raymond Heckert
2002-02-22 15:56:39 UTC
Re: [CAD_CAM_EDM_DRO] Auto tool changers
Doug Harrison
2002-02-22 16:02:18 UTC
Re: [CAD_CAM_EDM_DRO] PLC Programming - anyone?
dave_ace_me
2002-02-22 21:23:36 UTC
Re: PLC Programming - anyone?
Chris Clough
2002-02-22 22:35:29 UTC
RE: [CAD_CAM_EDM_DRO] Re: PLC Programming - anyone?
dave_ace_me
2002-02-23 05:26:56 UTC
Re: PLC Programming - anyone?
dave_ace_me
2002-02-23 05:41:56 UTC
Re: PLC Programming - anyone?
rekmac
2002-02-23 07:03:23 UTC
Re: PLC Programming - anyone?
ballendo
2002-02-23 08:18:48 UTC
Re: Auto tool changers
ballendo
2002-02-23 08:30:03 UTC
Re: Auto tool changers
Sven Peter
2002-02-23 08:32:07 UTC
Re: [CAD_CAM_EDM_DRO] PLC Programming - anyone?
Alan Marconett KM6VV
2002-02-23 10:17:03 UTC
Re: Auto tool changers
rekmac
2002-02-23 10:54:17 UTC
Re: Auto tool changers
Alan Marconett KM6VV
2002-02-23 11:36:16 UTC
Re: Auto tool changers
wanliker@a...
2002-02-23 12:40:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers
wanliker@a...
2002-02-23 12:49:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers
doug98105
2002-02-23 12:58:44 UTC
Re: Auto tool changers
Alan Marconett KM6VV
2002-02-23 14:11:37 UTC
Re: Auto tool changers
Smoke
2002-02-23 14:24:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers
wanliker@a...
2002-02-23 15:01:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers
doug98105
2002-02-23 15:36:57 UTC
Re: Auto tool changers
ballendo
2002-02-23 15:36:58 UTC
Re: Auto tool changers (more)
ballendo
2002-02-23 15:58:01 UTC
Re: Auto tool changers
ballendo
2002-02-23 16:04:10 UTC
Re: Auto tool changers
ballendo
2002-02-23 16:12:28 UTC
Re: Auto tool changers
John H.
2002-02-23 16:59:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers (more)
Alan Marconett KM6VV
2002-02-23 17:09:14 UTC
Re: Auto tool changers (more)
Alan Marconett KM6VV
2002-02-23 17:15:45 UTC
Re: Auto tool changers
Smoke
2002-02-23 18:13:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers
doug98105
2002-02-23 18:44:04 UTC
Re: Auto tool changers
Smoke
2002-02-23 20:32:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers
ballendo
2002-02-24 10:46:09 UTC
Re: Auto tool changers (more)
ballendo
2002-02-24 23:59:32 UTC
Re: Auto tool changers
rehenry
2002-02-25 06:11:10 UTC
Re: Re: Auto tool changers
imserv1
2002-02-25 08:04:28 UTC
Re: Auto tool changers
Brian Pitt
2002-02-25 09:28:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Auto tool changers
Alan Marconett KM6VV
2002-02-25 10:57:02 UTC
Re: Auto tool changers
John H.
2002-02-25 14:39:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers
Raymond Heckert
2002-02-25 17:50:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers
ballendo
2002-02-26 02:24:49 UTC
Re: Auto tool changers
ballendo
2002-02-26 03:49:20 UTC
Re: Auto tool changers
stephen_stallings
2002-02-26 10:24:38 UTC
Re: Auto tool changers - preloading
imserv1
2002-02-26 14:53:04 UTC
Re: Auto tool changers - preloading
wanliker@a...
2002-02-26 16:07:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers - preloading
imserv1
2002-02-26 19:01:24 UTC
Re: Auto tool changers - preloading
John H.
2002-02-26 20:37:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers
rehenry
2002-02-27 10:13:39 UTC
Re: Re: Auto tool changers
Scot Rogers
2002-02-27 21:47:49 UTC
RE: [CAD_CAM_EDM_DRO] Re: Auto tool changers
ballendo
2002-02-28 03:31:40 UTC
Re: Auto tool changers