CAD CAM EDM DRO - Yahoo Group Archive

Re: Re: Auto tool changers

Posted by rehenry
on 2002-02-25 06:11:10 UTC
>    From: "ballendo" <ballendo@...>

> Alan,
>
> Sounds like you're most of the way already...
>
> Yes, M06 and Txx. Most good programmers will list the "T" word at
> least a few blocks ahead of the M06, so the toolchange turret
> can "get ready"(rotate; talking 'bout mills here) so as to have the
> next tool in position for a quicker tool change when the M06 actually
> initiates the physical change to the new tool.
>
> But you have to be careful. Some controls will switch the offsets
> used WHEN the "T" word is read. Bad, very bad. Same old, same old;
> know your control! (Offsets "should" switch with the "D" and "H"
> words. (Some older controls use different letter addresses for
> diameter and height offset values)  

Ballendo

Now you've got me really confused with this program it before you use it
stuff. It has been my impression over the years that the combination of
look ahead and programmable logic handled these kinds of tool changer
specific problems in most commercial CNC/PLC's. I don't believe that
I've ever seen a program where the M6 Txx command was given before it was
needed. Could you list a sample of controls where this kind of
programming is commonly used?

You are right that as hobby users we need to clarify how a specific
CNC/PLC "reads" the M6, Txx, Dxx, and Hxx commands before we rush into
fitting or retrofitting.

RayH -- U.P. Michigan

Discussion Thread

John H. 2002-02-21 22:08:45 UTC Auto tool changers audiomaker2000 2002-02-22 03:33:21 UTC Re: Auto tool changers David M. Munro 2002-02-22 04:14:12 UTC Re: [CAD_CAM_EDM_DRO] Auto tool changers dave_ace_me 2002-02-22 04:25:26 UTC Re: Auto tool changers Smoke 2002-02-22 06:14:23 UTC Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers wanliker@a... 2002-02-22 07:05:58 UTC Re: [CAD_CAM_EDM_DRO] Auto tool changers Marcus & Eva 2002-02-22 07:24:41 UTC Re: [CAD_CAM_EDM_DRO] Auto tool changers ballendo 2002-02-22 08:03:12 UTC Re: Auto tool changers Drew Rogge 2002-02-22 08:16:15 UTC Re: [CAD_CAM_EDM_DRO] Auto tool changers Alan Marconett KM6VV 2002-02-22 11:41:34 UTC Re: [CAD_CAM_EDM_DRO] Auto tool changers Drew Rogge 2002-02-22 11:49:37 UTC Re: [CAD_CAM_EDM_DRO] Auto tool changers Alan Marconett KM6VV 2002-02-22 13:07:10 UTC Re: [CAD_CAM_EDM_DRO] Auto tool changers John H. 2002-02-22 13:13:40 UTC Re: [CAD_CAM_EDM_DRO] Auto tool changers wanliker@a... 2002-02-22 14:09:18 UTC Re: [CAD_CAM_EDM_DRO] Auto tool changers wanliker@a... 2002-02-22 14:11:08 UTC Re: [CAD_CAM_EDM_DRO] Auto tool changers wanliker@a... 2002-02-22 14:59:20 UTC Re: [CAD_CAM_EDM_DRO] Auto tool changers wanliker@a... 2002-02-22 15:26:11 UTC Re: [CAD_CAM_EDM_DRO] Auto tool changers Chris Clough 2002-02-22 15:30:12 UTC PLC Programming - anyone? Raymond Heckert 2002-02-22 15:56:39 UTC Re: [CAD_CAM_EDM_DRO] Auto tool changers Doug Harrison 2002-02-22 16:02:18 UTC Re: [CAD_CAM_EDM_DRO] PLC Programming - anyone? dave_ace_me 2002-02-22 21:23:36 UTC Re: PLC Programming - anyone? Chris Clough 2002-02-22 22:35:29 UTC RE: [CAD_CAM_EDM_DRO] Re: PLC Programming - anyone? dave_ace_me 2002-02-23 05:26:56 UTC Re: PLC Programming - anyone? dave_ace_me 2002-02-23 05:41:56 UTC Re: PLC Programming - anyone? rekmac 2002-02-23 07:03:23 UTC Re: PLC Programming - anyone? ballendo 2002-02-23 08:18:48 UTC Re: Auto tool changers ballendo 2002-02-23 08:30:03 UTC Re: Auto tool changers Sven Peter 2002-02-23 08:32:07 UTC Re: [CAD_CAM_EDM_DRO] PLC Programming - anyone? Alan Marconett KM6VV 2002-02-23 10:17:03 UTC Re: Auto tool changers rekmac 2002-02-23 10:54:17 UTC Re: Auto tool changers Alan Marconett KM6VV 2002-02-23 11:36:16 UTC Re: Auto tool changers wanliker@a... 2002-02-23 12:40:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers wanliker@a... 2002-02-23 12:49:28 UTC Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers doug98105 2002-02-23 12:58:44 UTC Re: Auto tool changers Alan Marconett KM6VV 2002-02-23 14:11:37 UTC Re: Auto tool changers Smoke 2002-02-23 14:24:16 UTC Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers wanliker@a... 2002-02-23 15:01:39 UTC Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers doug98105 2002-02-23 15:36:57 UTC Re: Auto tool changers ballendo 2002-02-23 15:36:58 UTC Re: Auto tool changers (more) ballendo 2002-02-23 15:58:01 UTC Re: Auto tool changers ballendo 2002-02-23 16:04:10 UTC Re: Auto tool changers ballendo 2002-02-23 16:12:28 UTC Re: Auto tool changers John H. 2002-02-23 16:59:41 UTC Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers (more) Alan Marconett KM6VV 2002-02-23 17:09:14 UTC Re: Auto tool changers (more) Alan Marconett KM6VV 2002-02-23 17:15:45 UTC Re: Auto tool changers Smoke 2002-02-23 18:13:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers doug98105 2002-02-23 18:44:04 UTC Re: Auto tool changers Smoke 2002-02-23 20:32:04 UTC Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers ballendo 2002-02-24 10:46:09 UTC Re: Auto tool changers (more) ballendo 2002-02-24 23:59:32 UTC Re: Auto tool changers rehenry 2002-02-25 06:11:10 UTC Re: Re: Auto tool changers imserv1 2002-02-25 08:04:28 UTC Re: Auto tool changers Brian Pitt 2002-02-25 09:28:25 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Auto tool changers Alan Marconett KM6VV 2002-02-25 10:57:02 UTC Re: Auto tool changers John H. 2002-02-25 14:39:40 UTC Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers Raymond Heckert 2002-02-25 17:50:20 UTC Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers ballendo 2002-02-26 02:24:49 UTC Re: Auto tool changers ballendo 2002-02-26 03:49:20 UTC Re: Auto tool changers stephen_stallings 2002-02-26 10:24:38 UTC Re: Auto tool changers - preloading imserv1 2002-02-26 14:53:04 UTC Re: Auto tool changers - preloading wanliker@a... 2002-02-26 16:07:22 UTC Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers - preloading imserv1 2002-02-26 19:01:24 UTC Re: Auto tool changers - preloading John H. 2002-02-26 20:37:10 UTC Re: [CAD_CAM_EDM_DRO] Re: Auto tool changers rehenry 2002-02-27 10:13:39 UTC Re: Re: Auto tool changers Scot Rogers 2002-02-27 21:47:49 UTC RE: [CAD_CAM_EDM_DRO] Re: Auto tool changers ballendo 2002-02-28 03:31:40 UTC Re: Auto tool changers