Re: [CAD_CAM_EDM_DRO] Steppers
Posted by
JanRwl@A...
on 2002-04-05 12:37:00 UTC
In a message dated 05-Apr-02 01:50:10 Central Standard Time,
capper@... writes:
connect the "DISABLE" to logic-gnd, and "all windings go
"open"!!!!!!!!!!!!!!!!!!!
[Non-text portions of this message have been removed]
capper@... writes:
> I was thinking of using relays to disconnect the stepper motors fromDuh... READ the terminals on the Gecko! Just temporarily (with a switch!)
> the geckos when I move the stage manually. Is this a good idea? Is there
> a easier way?
connect the "DISABLE" to logic-gnd, and "all windings go
"open"!!!!!!!!!!!!!!!!!!!
[Non-text portions of this message have been removed]
Discussion Thread
twil62551@a...
1999-07-03 20:35:46 UTC
Steppers
Ian W. Wright
1999-09-03 14:58:01 UTC
Steppers
DRigotti@a...
1999-09-03 19:38:45 UTC
Re: Steppers
Ian W. Wright
1999-09-04 03:19:53 UTC
Re: Steppers
Dan Mauch
1999-09-04 08:41:30 UTC
Re: Steppers
Charles Hopkins
2000-01-19 09:27:15 UTC
Steppers
Les Watts
2000-01-19 11:24:43 UTC
Re: Steppers
Matt Shaver
2000-01-19 12:09:16 UTC
Re: Steppers
Jon Elson
2000-01-19 21:26:52 UTC
Re: Steppers
Charles Hopkins
2000-01-20 09:03:20 UTC
RE: Steppers
Charles Hopkins
2000-01-20 09:34:08 UTC
RE: Steppers
Matt Shaver
2000-01-20 10:26:34 UTC
Re: Steppers
Matt Shaver
2000-01-20 10:28:41 UTC
Re: Steppers
Bob Campbell
2000-01-20 12:46:07 UTC
Re: Steppers
Harrison, Doug
2000-01-20 11:47:00 UTC
RE: Steppers
Gene
2002-03-31 01:01:22 UTC
Steppers
Ron Thompson
2002-03-31 07:01:57 UTC
Re: [CAD_CAM_EDM_DRO] Steppers
Alan Rothenbush
2002-03-31 07:56:31 UTC
Re: Steppers
JanRwl@A...
2002-03-31 13:21:12 UTC
Re: [CAD_CAM_EDM_DRO] Steppers
Alan Marconett KM6VV
2002-03-31 15:32:46 UTC
Re: [CAD_CAM_EDM_DRO] Steppers
andrewyslee
2002-03-31 22:39:49 UTC
Re: Steppers
dave_ace_me
2002-04-01 08:52:38 UTC
Steppers on a shaper (was Re: Steppers
Gene
2002-04-01 09:16:19 UTC
Re: [CAD_CAM_EDM_DRO] Steppers on a shaper (was Re: Steppers
Alan Marconett KM6VV
2002-04-01 13:28:54 UTC
Re: Steppers
Gene
2002-04-04 23:49:26 UTC
Steppers
JanRwl@A...
2002-04-05 12:37:00 UTC
Re: [CAD_CAM_EDM_DRO] Steppers
Tim Goldstein
2002-04-06 21:17:18 UTC
RE: [CAD_CAM_EDM_DRO] Steppers
ballendo
2002-04-13 03:21:53 UTC
Steppers on a shaper (was Re: Steppers
Gene
2002-11-26 01:50:47 UTC
Steppers
caudlet
2002-11-26 08:59:03 UTC
Re: Steppers
Tim Goldstein
2002-11-26 10:40:27 UTC
Re: [CAD_CAM_EDM_DRO] Steppers
Greg Jackson
2002-11-26 18:25:23 UTC
RE: [CAD_CAM_EDM_DRO] Steppers
Tim Goldstein
2002-11-26 22:49:40 UTC
RE: [CAD_CAM_EDM_DRO] Steppers
Gene
2002-12-02 21:06:12 UTC
Steppers
caudlet
2002-12-03 05:41:25 UTC
Re: Steppers
Gene
2004-05-05 14:12:12 UTC
Steppers
Michael Johnston
2004-05-05 14:26:21 UTC
RE: [CAD_CAM_EDM_DRO] Steppers
Jon Elson
2004-05-05 20:25:02 UTC
Re: [CAD_CAM_EDM_DRO] Steppers
JanRwl@A...
2004-05-05 20:56:09 UTC
Re: [CAD_CAM_EDM_DRO] Steppers
Michael Johnston
2004-05-05 21:08:40 UTC
RE: [CAD_CAM_EDM_DRO] Steppers
Nick Ibbitson
2004-05-07 13:13:20 UTC
Re: [CAD_CAM_EDM_DRO] Steppers
Gene
2004-08-17 10:57:09 UTC
Steppers
Jon Elson
2004-08-18 03:13:11 UTC
Re: [CAD_CAM_EDM_DRO] Steppers
krashking405
2006-07-19 15:22:54 UTC
Steppers