CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] Steppers

on 2004-05-05 21:08:40 UTC
You are absolutely right. Thank you for correcting me. The Gecko stepper
drivers are 7 amp and not 10. I was going from memory and didn't check my
facts. You know what they say, the memory is always the SECOND thing to go.

Damn! I hate it when I'm wrong. ;(

-----Original Message-----
From: Jon Elson [mailto:elson@...]
Sent: Wednesday, May 05, 2004 8:22 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] Steppers

Michael Johnston wrote:
>One revolution has 360 degrees. 360 degrees divided by 200 steps equals
1.8
>degrees per step. So, all three motors are actually equivalent in their
>rotational accuracy. They just express the measurement differently: 200
>steps vs 1.8 degrees means the same thing. The Gecko drive will handle up
>to 10 amps so I would think you should be OK.
>
>
No, the Gecko 201 and 210 drives are only 7 Amp, not 10!

See their web page, it is right on the front page.

Jon

Discussion Thread

twil62551@a... 1999-07-03 20:35:46 UTC Steppers Ian W. Wright 1999-09-03 14:58:01 UTC Steppers DRigotti@a... 1999-09-03 19:38:45 UTC Re: Steppers Ian W. Wright 1999-09-04 03:19:53 UTC Re: Steppers Dan Mauch 1999-09-04 08:41:30 UTC Re: Steppers Charles Hopkins 2000-01-19 09:27:15 UTC Steppers Les Watts 2000-01-19 11:24:43 UTC Re: Steppers Matt Shaver 2000-01-19 12:09:16 UTC Re: Steppers Jon Elson 2000-01-19 21:26:52 UTC Re: Steppers Charles Hopkins 2000-01-20 09:03:20 UTC RE: Steppers Charles Hopkins 2000-01-20 09:34:08 UTC RE: Steppers Matt Shaver 2000-01-20 10:26:34 UTC Re: Steppers Matt Shaver 2000-01-20 10:28:41 UTC Re: Steppers Bob Campbell 2000-01-20 12:46:07 UTC Re: Steppers Harrison, Doug 2000-01-20 11:47:00 UTC RE: Steppers Gene 2002-03-31 01:01:22 UTC Steppers Ron Thompson 2002-03-31 07:01:57 UTC Re: [CAD_CAM_EDM_DRO] Steppers Alan Rothenbush 2002-03-31 07:56:31 UTC Re: Steppers JanRwl@A... 2002-03-31 13:21:12 UTC Re: [CAD_CAM_EDM_DRO] Steppers Alan Marconett KM6VV 2002-03-31 15:32:46 UTC Re: [CAD_CAM_EDM_DRO] Steppers andrewyslee 2002-03-31 22:39:49 UTC Re: Steppers dave_ace_me 2002-04-01 08:52:38 UTC Steppers on a shaper (was Re: Steppers Gene 2002-04-01 09:16:19 UTC Re: [CAD_CAM_EDM_DRO] Steppers on a shaper (was Re: Steppers Alan Marconett KM6VV 2002-04-01 13:28:54 UTC Re: Steppers Gene 2002-04-04 23:49:26 UTC Steppers JanRwl@A... 2002-04-05 12:37:00 UTC Re: [CAD_CAM_EDM_DRO] Steppers Tim Goldstein 2002-04-06 21:17:18 UTC RE: [CAD_CAM_EDM_DRO] Steppers ballendo 2002-04-13 03:21:53 UTC Steppers on a shaper (was Re: Steppers Gene 2002-11-26 01:50:47 UTC Steppers caudlet 2002-11-26 08:59:03 UTC Re: Steppers Tim Goldstein 2002-11-26 10:40:27 UTC Re: [CAD_CAM_EDM_DRO] Steppers Greg Jackson 2002-11-26 18:25:23 UTC RE: [CAD_CAM_EDM_DRO] Steppers Tim Goldstein 2002-11-26 22:49:40 UTC RE: [CAD_CAM_EDM_DRO] Steppers Gene 2002-12-02 21:06:12 UTC Steppers caudlet 2002-12-03 05:41:25 UTC Re: Steppers Gene 2004-05-05 14:12:12 UTC Steppers Michael Johnston 2004-05-05 14:26:21 UTC RE: [CAD_CAM_EDM_DRO] Steppers Jon Elson 2004-05-05 20:25:02 UTC Re: [CAD_CAM_EDM_DRO] Steppers JanRwl@A... 2004-05-05 20:56:09 UTC Re: [CAD_CAM_EDM_DRO] Steppers Michael Johnston 2004-05-05 21:08:40 UTC RE: [CAD_CAM_EDM_DRO] Steppers Nick Ibbitson 2004-05-07 13:13:20 UTC Re: [CAD_CAM_EDM_DRO] Steppers Gene 2004-08-17 10:57:09 UTC Steppers Jon Elson 2004-08-18 03:13:11 UTC Re: [CAD_CAM_EDM_DRO] Steppers krashking405 2006-07-19 15:22:54 UTC Steppers