CAD CAM EDM DRO - Yahoo Group Archive

GECKOS 201

Posted by ralaco
on 2002-11-26 15:48:28 UTC
The power supply to run 4 4amp stepper motors with Geckos 201.
Can it be made with a 36 volts 16 amp transformer, a bridge rectifier
and the same 10,000uF 63VDC capacitor?

Raul Lara

Discussion Thread

ralaco 2002-11-26 15:48:28 UTC GECKOS 201 turbulatordude 2002-11-26 16:03:02 UTC Re: GECKOS 201 ralaco 2002-11-26 17:10:03 UTC Re: GECKOS 201 turbulatordude 2002-11-26 19:19:11 UTC Re: GECKOS 201 ralaco 2002-11-27 08:37:13 UTC Re: GECKOS 201 j.guenther 2002-11-27 08:44:21 UTC RE: [CAD_CAM_EDM_DRO] Re: GECKOS 201 ralaco 2002-11-27 08:47:26 UTC Re: GECKOS 201 caudlet 2002-11-27 09:09:39 UTC Re: GECKOS 201 Kory Hamzeh 2002-11-27 10:32:56 UTC RE: [CAD_CAM_EDM_DRO] Re: GECKOS 201 Carol & Jerry Jankura 2002-11-27 10:41:21 UTC RE: [CAD_CAM_EDM_DRO] Re: GECKOS 201 caudlet 2002-11-27 11:47:53 UTC Re: GECKOS 201 turbulatordude 2002-11-27 13:22:31 UTC Re: GECKOS 201 Peter Homann 2002-11-27 15:01:09 UTC G Code for 25 Pin D connector deanc500 2002-11-27 16:45:38 UTC Re: G Code for 25 Pin D connector Robert Campbell 2002-11-27 17:13:08 UTC Re: [CAD_CAM_EDM_DRO] G Code for 25 Pin D connector JanRwl@A... 2002-11-27 19:07:53 UTC Re: [CAD_CAM_EDM_DRO] Re: GECKOS 201 JanRwl@A... 2002-11-27 19:25:23 UTC Re: [CAD_CAM_EDM_DRO] Re: GECKOS 201 Peter Homann 2002-11-27 19:56:09 UTC RE: [CAD_CAM_EDM_DRO] Re: G Code for 25 Pin D connector Peter Homann 2002-11-27 20:39:59 UTC RE: [CAD_CAM_EDM_DRO] G Code for 25 Pin D connector turbulatordude 2002-11-28 08:47:58 UTC Re: GECKOS 201 Dan Mauch 2002-11-29 07:25:07 UTC RE: [CAD_CAM_EDM_DRO] Re: GECKOS 201 turbulatordude 2002-11-29 09:50:46 UTC to Low ESR or not to Low ESR, that is the ... ( was Re: GECKOS 201 jeffalanp 2002-11-29 10:49:50 UTC to Low ESR or not to Low ESR, that is the ... ( was Re: GECKOS 201 JanRwl@A... 2002-11-29 10:56:20 UTC Re: [CAD_CAM_EDM_DRO] Re: GECKOS 201 turbulatordude 2002-11-29 19:15:26 UTC to Low ESR or not to Low ESR, that is the ... ( was Re: GECKOS 201 Tim Goldstein 2002-11-29 19:51:10 UTC RE: [CAD_CAM_EDM_DRO] to Low ESR or not to Low ESR, that is the ... ( was Re: GECKOS 201 jeffalanp 2002-11-29 21:52:45 UTC to Low ESR or not to Low ESR, that is the ... ( was Re: GECKOS 201 turbulatordude 2002-11-30 06:40:31 UTC to Low ESR or not to Low ESR, that is the ... ( was Re: GECKOS 201