RE: [CAD_CAM_EDM_DRO] Re: GECKOS 201
Posted by
Kory Hamzeh
on 2002-11-27 10:32:56 UTC
>Hi Raul,
> I can't find a capacitor that big here in Monterrey, Mexico.
Put several of the capacitors in parallel, observing the polarity. The total
capacitance because the sum of all off the capacitors.
Good luck,
Kory
Discussion Thread
ralaco
2002-11-26 15:48:28 UTC
GECKOS 201
turbulatordude
2002-11-26 16:03:02 UTC
Re: GECKOS 201
ralaco
2002-11-26 17:10:03 UTC
Re: GECKOS 201
turbulatordude
2002-11-26 19:19:11 UTC
Re: GECKOS 201
ralaco
2002-11-27 08:37:13 UTC
Re: GECKOS 201
j.guenther
2002-11-27 08:44:21 UTC
RE: [CAD_CAM_EDM_DRO] Re: GECKOS 201
ralaco
2002-11-27 08:47:26 UTC
Re: GECKOS 201
caudlet
2002-11-27 09:09:39 UTC
Re: GECKOS 201
Kory Hamzeh
2002-11-27 10:32:56 UTC
RE: [CAD_CAM_EDM_DRO] Re: GECKOS 201
Carol & Jerry Jankura
2002-11-27 10:41:21 UTC
RE: [CAD_CAM_EDM_DRO] Re: GECKOS 201
caudlet
2002-11-27 11:47:53 UTC
Re: GECKOS 201
turbulatordude
2002-11-27 13:22:31 UTC
Re: GECKOS 201
Peter Homann
2002-11-27 15:01:09 UTC
G Code for 25 Pin D connector
deanc500
2002-11-27 16:45:38 UTC
Re: G Code for 25 Pin D connector
Robert Campbell
2002-11-27 17:13:08 UTC
Re: [CAD_CAM_EDM_DRO] G Code for 25 Pin D connector
JanRwl@A...
2002-11-27 19:07:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: GECKOS 201
JanRwl@A...
2002-11-27 19:25:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: GECKOS 201
Peter Homann
2002-11-27 19:56:09 UTC
RE: [CAD_CAM_EDM_DRO] Re: G Code for 25 Pin D connector
Peter Homann
2002-11-27 20:39:59 UTC
RE: [CAD_CAM_EDM_DRO] G Code for 25 Pin D connector
turbulatordude
2002-11-28 08:47:58 UTC
Re: GECKOS 201
Dan Mauch
2002-11-29 07:25:07 UTC
RE: [CAD_CAM_EDM_DRO] Re: GECKOS 201
turbulatordude
2002-11-29 09:50:46 UTC
to Low ESR or not to Low ESR, that is the ... ( was Re: GECKOS 201
jeffalanp
2002-11-29 10:49:50 UTC
to Low ESR or not to Low ESR, that is the ... ( was Re: GECKOS 201
JanRwl@A...
2002-11-29 10:56:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: GECKOS 201
turbulatordude
2002-11-29 19:15:26 UTC
to Low ESR or not to Low ESR, that is the ... ( was Re: GECKOS 201
Tim Goldstein
2002-11-29 19:51:10 UTC
RE: [CAD_CAM_EDM_DRO] to Low ESR or not to Low ESR, that is the ... ( was Re: GECKOS 201
jeffalanp
2002-11-29 21:52:45 UTC
to Low ESR or not to Low ESR, that is the ... ( was Re: GECKOS 201
turbulatordude
2002-11-30 06:40:31 UTC
to Low ESR or not to Low ESR, that is the ... ( was Re: GECKOS 201