G Code for 25 Pin D connector
Posted by
Peter Homann
on 2002-11-27 15:01:09 UTC
Hi,
I'm looking to put my controller board in an enclosure. Does anyone have G
Code for cutting out a hole for a 25 Pin D connector that they could share?
As another thought, I might be useful to set up a library of useful G Code
snippets. Or is there one already?
Cheers,
Peter Homann
mailto:Peter.Homann@...
Adacel Technologies Limited,
250 Bay St, BRIGHTON, 3186, AUSTRALIA
http://www.adacel.com <http://www.adacel.com>
Telephone +61 (3) 8530 7777, Facsimile +61 (3) 9596 2960
Mobile 0421-601 665
I'm looking to put my controller board in an enclosure. Does anyone have G
Code for cutting out a hole for a 25 Pin D connector that they could share?
As another thought, I might be useful to set up a library of useful G Code
snippets. Or is there one already?
Cheers,
Peter Homann
mailto:Peter.Homann@...
Adacel Technologies Limited,
250 Bay St, BRIGHTON, 3186, AUSTRALIA
http://www.adacel.com <http://www.adacel.com>
Telephone +61 (3) 8530 7777, Facsimile +61 (3) 9596 2960
Mobile 0421-601 665
Discussion Thread
ralaco
2002-11-26 15:48:28 UTC
GECKOS 201
turbulatordude
2002-11-26 16:03:02 UTC
Re: GECKOS 201
ralaco
2002-11-26 17:10:03 UTC
Re: GECKOS 201
turbulatordude
2002-11-26 19:19:11 UTC
Re: GECKOS 201
ralaco
2002-11-27 08:37:13 UTC
Re: GECKOS 201
j.guenther
2002-11-27 08:44:21 UTC
RE: [CAD_CAM_EDM_DRO] Re: GECKOS 201
ralaco
2002-11-27 08:47:26 UTC
Re: GECKOS 201
caudlet
2002-11-27 09:09:39 UTC
Re: GECKOS 201
Kory Hamzeh
2002-11-27 10:32:56 UTC
RE: [CAD_CAM_EDM_DRO] Re: GECKOS 201
Carol & Jerry Jankura
2002-11-27 10:41:21 UTC
RE: [CAD_CAM_EDM_DRO] Re: GECKOS 201
caudlet
2002-11-27 11:47:53 UTC
Re: GECKOS 201
turbulatordude
2002-11-27 13:22:31 UTC
Re: GECKOS 201
Peter Homann
2002-11-27 15:01:09 UTC
G Code for 25 Pin D connector
deanc500
2002-11-27 16:45:38 UTC
Re: G Code for 25 Pin D connector
Robert Campbell
2002-11-27 17:13:08 UTC
Re: [CAD_CAM_EDM_DRO] G Code for 25 Pin D connector
JanRwl@A...
2002-11-27 19:07:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: GECKOS 201
JanRwl@A...
2002-11-27 19:25:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: GECKOS 201
Peter Homann
2002-11-27 19:56:09 UTC
RE: [CAD_CAM_EDM_DRO] Re: G Code for 25 Pin D connector
Peter Homann
2002-11-27 20:39:59 UTC
RE: [CAD_CAM_EDM_DRO] G Code for 25 Pin D connector
turbulatordude
2002-11-28 08:47:58 UTC
Re: GECKOS 201
Dan Mauch
2002-11-29 07:25:07 UTC
RE: [CAD_CAM_EDM_DRO] Re: GECKOS 201
turbulatordude
2002-11-29 09:50:46 UTC
to Low ESR or not to Low ESR, that is the ... ( was Re: GECKOS 201
jeffalanp
2002-11-29 10:49:50 UTC
to Low ESR or not to Low ESR, that is the ... ( was Re: GECKOS 201
JanRwl@A...
2002-11-29 10:56:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: GECKOS 201
turbulatordude
2002-11-29 19:15:26 UTC
to Low ESR or not to Low ESR, that is the ... ( was Re: GECKOS 201
Tim Goldstein
2002-11-29 19:51:10 UTC
RE: [CAD_CAM_EDM_DRO] to Low ESR or not to Low ESR, that is the ... ( was Re: GECKOS 201
jeffalanp
2002-11-29 21:52:45 UTC
to Low ESR or not to Low ESR, that is the ... ( was Re: GECKOS 201
turbulatordude
2002-11-30 06:40:31 UTC
to Low ESR or not to Low ESR, that is the ... ( was Re: GECKOS 201