CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Re: Belt vs. Direct Drive

Posted by Jon Elson
on 2003-01-05 23:12:49 UTC
alex wrote:

> Jon.
>Yes, anti-backlash screw should make it very rigid - so probably I will go
>this root.
>I checked your products and they seem to represent a great value for the
>money.
>Its amazing what people can have now for a few hundred dollars. I was
>looking
>at the recent KBC tool flier - Basic milling machine is $6,625 Cdn.
>The same machine with 2 axis CNC - $25,000 Cdn. I think, using your staff,
>the same
>conversion can be done within $10,000 Cdn. Not a bad saving!
>
>
Unless you want high-resolution linear scales, I think you can do this
for a LOT less than 10 K,
even those smaller Cdn $! The ballscrews will be the most expensive
part, probably. In US $,
these run somewhere between $800 and 1200, I think. You should be able
to find decent encoders
for about $100 ea. with a little looking, sometimes much lower on eBay.
Servo motors should
be available surplus under $100 ea. Expect $250 or so for pulleys and
sprockets. Gecko Drives
are under $200 ea. My stepper driver board is $200. So, that comes to
something like US $2600
for a 3 axis conversion. Depending on how good a scrounger you are, you
might even be able
to do better.

Jon

Discussion Thread

dennis_kramer2001 <dennis.kramer@a... 2003-01-02 17:14:08 UTC Belt vs. Direct Drive Robert Campbell 2003-01-02 17:51:28 UTC Re: [CAD_CAM_EDM_DRO] Belt vs. Direct Drive Doug Fortune 2003-01-02 18:51:25 UTC Re: [CAD_CAM_EDM_DRO] Belt vs. Direct Drive Chris Baugher 2003-01-02 19:18:13 UTC Re: [CAD_CAM_EDM_DRO] Belt vs. Direct Drive Doug Fortune 2003-01-03 01:11:21 UTC Re: [CAD_CAM_EDM_DRO] Belt vs. Direct Drive Tony Jeffree <tony@j... 2003-01-03 01:17:12 UTC Re: Belt vs. Direct Drive jeffalanp <xylotex@h... 2003-01-03 01:19:14 UTC Re: Belt vs. Direct Drive torsten98001 <torsten@g... 2003-01-03 03:02:04 UTC Re: Belt vs. Direct Drive bjammin@i... 2003-01-03 07:26:21 UTC Re: [CAD_CAM_EDM_DRO] Re: Belt vs. Direct Drive Marv Frankel 2003-01-03 08:06:06 UTC Re: [CAD_CAM_EDM_DRO] Re: Belt vs. Direct Drive Garry & Maxine Foster 2003-01-03 08:27:42 UTC Re: [CAD_CAM_EDM_DRO] Re: Belt vs. Direct Drive CL 2003-01-03 10:58:51 UTC Re: [CAD_CAM_EDM_DRO] Belt vs. Direct Drive CL 2003-01-03 11:23:46 UTC Re: [CAD_CAM_EDM_DRO] Re: Belt vs. Direct Drive alex 2003-01-03 11:34:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Belt vs. Direct Drive Tim Goldstein 2003-01-03 11:46:55 UTC Re: [CAD_CAM_EDM_DRO] Re: Belt vs. Direct Drive Chris Baugher 2003-01-03 12:13:01 UTC Re: [CAD_CAM_EDM_DRO] Belt vs. Direct Drive Chris Baugher 2003-01-03 18:31:50 UTC Re: [CAD_CAM_EDM_DRO] Re: Belt vs. Direct Drive jeffalanp <xylotex@h... 2003-01-03 18:43:49 UTC Re: Belt vs. Direct Drive Tony Jeffree 2003-01-03 21:51:52 UTC Re: Re: Belt vs. Direct Drive Tony Jeffree 2003-01-03 22:14:42 UTC Re: Re: Belt vs. Direct Drive bjammin@i... 2003-01-04 00:00:29 UTC Re: [CAD_CAM_EDM_DRO] Re: Belt vs. Direct Drive Tim Goldstein 2003-01-04 10:38:57 UTC RE: [CAD_CAM_EDM_DRO] Re: Re: Belt vs. Direct Drive alex 2003-01-04 16:24:30 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Belt vs. Direct Drive Ron Kline 2003-01-04 16:58:01 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Belt vs. Direct Drive alex 2003-01-04 17:33:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Belt vs. Direct Drive jwalters 2003-01-04 18:13:50 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Belt vs. Direct Drive Dave Kowalczyk <dkowalcz@d... 2003-01-04 18:53:19 UTC Re: Belt vs. Direct Drive Ron Kline 2003-01-04 20:11:18 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Belt vs. Direct Drive Jon Elson 2003-01-04 22:26:08 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Belt vs. Direct Drive alex 2003-01-05 15:45:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Belt vs. Direct Drive Jon Elson 2003-01-05 23:12:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Belt vs. Direct Drive alex 2003-01-08 08:12:32 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Belt vs. Direct Drive Jon Elson 2003-01-08 23:26:42 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Belt vs. Direct Drive