CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Power supplies

Posted by Jon Elson
on 2003-07-27 22:23:11 UTC
mmeyers1111 wrote:

>ASSUMPTIONS:
>CNC router table with 3 Gecko G201 drives and 3 NEMA 34 steppers
>
>QUESTIONS:
>1)Has anybody seen/purchased this 50v 3amp power supply...
>
>
I think 3 Amps is too small. I think you might find a 7 Amp regulated
supply
would be about the minimum that will work. On the onter hand, a 5-7 Amp
UNREGULATED supply probably will work a lot better. it has the capability
to supply short bursts of current well above the continuous rating. The
regulated supply will dip severely in voltage right above the rating (or
wherever you set the current limit at).

>http://www.web-tronics.com/30serdigrobe.html
>
>and could it be used to power the drives and motors?
>
>If not, can somebody suggest a power supply in the $100 or so range
>that woudl fit the bill?
>
>
Jameco has a 48 V 10.4A power supply available for $69.95, their part
no. is 202913CD. This is a switching supply, and regulated, but it is
obviously beefy enough. I can't find any better deals in unregulated
supplies at the moment.

>2) Assuming I buy a power supply such as the one described, what
>might I have to put between the power supply and the drives other
>than a fuse for each drive?
>
>
>
If you use a fuse, Gecko recommends placing a capacitor across the
power input terminals. See the data sheet for the drive.

Jon

Discussion Thread

galt1x 2002-05-29 19:01:31 UTC Power supplies illya 2002-05-29 19:18:24 UTC Re: [CAD_CAM_EDM_DRO] Power supplies illya 2002-05-29 19:32:56 UTC Re: [CAD_CAM_EDM_DRO] Power supplies illya 2002-05-29 19:45:31 UTC Re: [CAD_CAM_EDM_DRO] Power supplies galt1x 2002-05-30 01:15:45 UTC Re: [CAD_CAM_EDM_DRO] Power supplies illya 2002-05-30 01:30:29 UTC Re: [CAD_CAM_EDM_DRO] Power supplies P. J. Hicks 2002-12-21 10:29:20 UTC Power supplies Tim Goldstein 2002-12-21 10:59:54 UTC RE: [CAD_CAM_EDM_DRO] Power supplies Alan Marconett KM6VV 2002-12-21 11:16:33 UTC Re: [CAD_CAM_EDM_DRO] Power supplies Robert Campbell 2002-12-21 11:19:46 UTC Re: [CAD_CAM_EDM_DRO] Power supplies turbulatordude <davemucha@j... 2002-12-21 11:34:47 UTC Re: Power supplies Ron Kline 2002-12-21 18:30:29 UTC Re: [CAD_CAM_EDM_DRO] Power supplies Todd Fleming 2002-12-21 18:45:45 UTC Re: [CAD_CAM_EDM_DRO] Power supplies Ron Kline 2002-12-21 19:06:41 UTC Re: [CAD_CAM_EDM_DRO] Power supplies Todd Fleming 2002-12-21 19:10:22 UTC Re: [CAD_CAM_EDM_DRO] Power supplies turbulatordude <davemucha@j... 2002-12-21 19:29:20 UTC Re: Power supplies Carol & Jerry Jankura 2002-12-21 19:53:02 UTC RE: [CAD_CAM_EDM_DRO] Power supplies Todd Fleming 2002-12-21 19:58:18 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supplies Paul Amaranth 2002-12-21 20:00:06 UTC Re: [CAD_CAM_EDM_DRO] Power supplies Hoyt McKagen 2002-12-21 22:05:53 UTC RE: [CAD_CAM_EDM_DRO] Power supplies Chris L 2002-12-21 22:50:15 UTC Re: [CAD_CAM_EDM_DRO] Power supplies turbulatordude <davemucha@j... 2002-12-22 09:07:33 UTC Re: Power supplies ( blown Gecko) JanRwl@A... 2002-12-22 16:59:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supplies ( blown Gecko) turbulatordude <davemucha@j... 2002-12-23 05:29:37 UTC Re: Power supplies ( blown Gecko) mmeyers1111 2003-07-27 21:54:40 UTC Power supplies Jon Elson 2003-07-27 22:23:11 UTC Re: [CAD_CAM_EDM_DRO] Power supplies turbulatordude 2003-07-28 06:56:04 UTC Re: Power supplies dougfennell2000 2003-07-28 13:43:52 UTC Re: Power supplies Dan Mauch 2003-07-28 16:33:54 UTC RE: [CAD_CAM_EDM_DRO] Re: Power supplies Robert Campbell 2003-07-28 17:56:33 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supplies mmeyers1111 2003-07-28 17:57:39 UTC Re: Power supplies Doug Fortune 2003-07-28 18:59:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supplies Tim Goldstein 2003-07-28 20:29:38 UTC RE: [CAD_CAM_EDM_DRO] Re: Power supplies dougfennell2000 2003-07-28 20:31:56 UTC Re: Power supplies dougfennell2000 2003-07-28 20:32:12 UTC Re: Power supplies Robert Campbell 2003-07-28 20:32:34 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supplies dougfennell2000 2003-07-28 20:33:15 UTC Re: Power supplies mmeyers1111 2003-07-29 00:06:45 UTC Re: Power supplies dougfennell2000 2003-07-29 07:12:56 UTC Re: Power supplies fortino 2003-07-29 07:39:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supplies mmeyers1111 2003-07-29 14:55:25 UTC Re: Power supplies wvickery2003 2005-02-21 09:18:05 UTC Power supplies braidmeister 2005-02-21 09:33:12 UTC Re: Power supplies turbulatordude 2005-02-21 09:44:18 UTC Re: Power supplies Dan Mauch 2005-02-21 09:58:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supplies wvickery2003 2005-02-21 10:02:22 UTC Re: Power supplies turbulatordude 2005-02-21 10:18:59 UTC Re: Power supplies turbulatordude 2005-02-21 11:01:56 UTC Re: Power supplies