CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Power supplies

Posted by Dan Mauch
on 2005-02-21 09:58:45 UTC
The xylotex unipolar board is designed to run at a max of 44VDC but
recommends the voltage be held to 34 +/-VDC for various reasons. And yes you
can run a stepper motor at 10 to 25 time it rated unipolar voltage if you
use a chopper driver.
Dan
----- Original Message -----
From: "turbulatordude" <dave_mucha@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Monday, February 21, 2005 9:38 AM
Subject: [CAD_CAM_EDM_DRO] Re: Power supplies


>
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "braidmeister"
> <braidmeister@y...> wrote:
>>
>> Warren,
>> Go to www.geckodrive.com and read the stepper motor white
> paper...and
>> other documents about power supplies etc. It will answer many of
> your
>> questions....Depending on what you want to do with your setup, I'd
>> say that you could use a 75v PS with those motors (but this depends
>> on the max voltage that the Xylotex will handle....I forget what
> that
>> is) You might be limited to something like 48v...which would be
> fine.
>> Read the info on gecko's site.
>>
>> -Brady
>
> As a general rule, steppers can be run up to about 25 times nameplate
> voltage WHEN USED with a chopper driver like the Gecko or Xylotex.
>
> Xylotex is rated for a power supply of about 28 volts max, with 24
> volts normal.
>
> You can buy a switching power supply, 24 volts and a few amps to
> handle those motors.
>
> Building one may be more expensive as the capacitors will need to be
> pretty big.
>
> Dave
>
>
>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
> timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
> [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
> if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
> sister site to the CCED group, as many of the same members are there, for
> OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
>

Discussion Thread

galt1x 2002-05-29 19:01:31 UTC Power supplies illya 2002-05-29 19:18:24 UTC Re: [CAD_CAM_EDM_DRO] Power supplies illya 2002-05-29 19:32:56 UTC Re: [CAD_CAM_EDM_DRO] Power supplies illya 2002-05-29 19:45:31 UTC Re: [CAD_CAM_EDM_DRO] Power supplies galt1x 2002-05-30 01:15:45 UTC Re: [CAD_CAM_EDM_DRO] Power supplies illya 2002-05-30 01:30:29 UTC Re: [CAD_CAM_EDM_DRO] Power supplies P. J. Hicks 2002-12-21 10:29:20 UTC Power supplies Tim Goldstein 2002-12-21 10:59:54 UTC RE: [CAD_CAM_EDM_DRO] Power supplies Alan Marconett KM6VV 2002-12-21 11:16:33 UTC Re: [CAD_CAM_EDM_DRO] Power supplies Robert Campbell 2002-12-21 11:19:46 UTC Re: [CAD_CAM_EDM_DRO] Power supplies turbulatordude <davemucha@j... 2002-12-21 11:34:47 UTC Re: Power supplies Ron Kline 2002-12-21 18:30:29 UTC Re: [CAD_CAM_EDM_DRO] Power supplies Todd Fleming 2002-12-21 18:45:45 UTC Re: [CAD_CAM_EDM_DRO] Power supplies Ron Kline 2002-12-21 19:06:41 UTC Re: [CAD_CAM_EDM_DRO] Power supplies Todd Fleming 2002-12-21 19:10:22 UTC Re: [CAD_CAM_EDM_DRO] Power supplies turbulatordude <davemucha@j... 2002-12-21 19:29:20 UTC Re: Power supplies Carol & Jerry Jankura 2002-12-21 19:53:02 UTC RE: [CAD_CAM_EDM_DRO] Power supplies Todd Fleming 2002-12-21 19:58:18 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supplies Paul Amaranth 2002-12-21 20:00:06 UTC Re: [CAD_CAM_EDM_DRO] Power supplies Hoyt McKagen 2002-12-21 22:05:53 UTC RE: [CAD_CAM_EDM_DRO] Power supplies Chris L 2002-12-21 22:50:15 UTC Re: [CAD_CAM_EDM_DRO] Power supplies turbulatordude <davemucha@j... 2002-12-22 09:07:33 UTC Re: Power supplies ( blown Gecko) JanRwl@A... 2002-12-22 16:59:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supplies ( blown Gecko) turbulatordude <davemucha@j... 2002-12-23 05:29:37 UTC Re: Power supplies ( blown Gecko) mmeyers1111 2003-07-27 21:54:40 UTC Power supplies Jon Elson 2003-07-27 22:23:11 UTC Re: [CAD_CAM_EDM_DRO] Power supplies turbulatordude 2003-07-28 06:56:04 UTC Re: Power supplies dougfennell2000 2003-07-28 13:43:52 UTC Re: Power supplies Dan Mauch 2003-07-28 16:33:54 UTC RE: [CAD_CAM_EDM_DRO] Re: Power supplies Robert Campbell 2003-07-28 17:56:33 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supplies mmeyers1111 2003-07-28 17:57:39 UTC Re: Power supplies Doug Fortune 2003-07-28 18:59:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supplies Tim Goldstein 2003-07-28 20:29:38 UTC RE: [CAD_CAM_EDM_DRO] Re: Power supplies dougfennell2000 2003-07-28 20:31:56 UTC Re: Power supplies dougfennell2000 2003-07-28 20:32:12 UTC Re: Power supplies Robert Campbell 2003-07-28 20:32:34 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supplies dougfennell2000 2003-07-28 20:33:15 UTC Re: Power supplies mmeyers1111 2003-07-29 00:06:45 UTC Re: Power supplies dougfennell2000 2003-07-29 07:12:56 UTC Re: Power supplies fortino 2003-07-29 07:39:58 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supplies mmeyers1111 2003-07-29 14:55:25 UTC Re: Power supplies wvickery2003 2005-02-21 09:18:05 UTC Power supplies braidmeister 2005-02-21 09:33:12 UTC Re: Power supplies turbulatordude 2005-02-21 09:44:18 UTC Re: Power supplies Dan Mauch 2005-02-21 09:58:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Power supplies wvickery2003 2005-02-21 10:02:22 UTC Re: Power supplies turbulatordude 2005-02-21 10:18:59 UTC Re: Power supplies turbulatordude 2005-02-21 11:01:56 UTC Re: Power supplies