Re: Power supplies

Also, for the Cap go to www.mistersprockets.com (call them, cause
you'll never find it on the website). Ask for a Comm grade capacitor
with screw type terminals in the 80V 2200mfd range - it dosen't have
to be exact, its just used to smooth out the DC ripple voltage.

Mouser part # for rectifier is 625-GBPC3510W 35A@1000V


--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Dan Mauch" <dmauch@s...>
wrote:

>
> What is the mouser part number for that transformer. I can't find

it at

> www.mouser.com
>
> Dan
> -----Original Message-----
> From: dougfennell2000 [mailto:dfennell@m...]
> Sent: Monday, July 28, 2003 10:55 AM
> To: CAD_CAM_EDM_DRO@yahoogroups.com
> Subject: [CAD_CAM_EDM_DRO] Re: Power supplies
>
>
> Recipe for a power supply:
>
> 1 50V 25A torid coil reansformer (mouser)
> 1 80v 2200mfd cap
> 1 1500v bridge rectifer (mouser)
> 1 power switch (250v 30a)
> 1 25a slow blow fuse and holder
> some wire
> something to put it all in (I used an old PC tower case)
> This supply will give you 68v at 25a EXACTLY after dc rectification
> and the anti ripple effect of the cap. It will last for years and

be

> a widowmaker of a power supply.
>
> Doug
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, "mmeyers1111"
> <mmeyers1111@y...> wrote:
> > ASSUMPTIONS:
> > CNC router table with 3 Gecko G201 drives and 3 NEMA 34 steppers
> >
> > QUESTIONS:
> > 1)Has anybody seen/purchased this 50v 3amp power supply...
> >
> > http://www.web-tronics.com/30serdigrobe.html
> >
> > and could it be used to power the drives and motors?
> >
> > If not, can somebody suggest a power supply in the $100 or so

range

> > that woudl fit the bill?
> >
> > 2) Assuming I buy a power supply such as the one described, what
> > might I have to put between the power supply and the drives other
> > than a fuse for each drive?
> >
> > Mike
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@a...,
> timg@k...
> Moderator: pentam@c... indigo_red@q... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to

reach it

> if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to

be a

> sister site to the CCED group, as many of the same members are

there,

> for OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING

THEM.

> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........ bill
> List Mom List Owner
>
>
>
> Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/