Re: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
Posted by
James Cullins
on 2003-09-17 06:30:51 UTC
If you are driving Geckos and supplying the 5v form the PC then on ground is
need. The circuit is completed inside the laptop.
I think the problem is the drive capability of a laptop may not be enough to
drive the
optoisolators. I us a 74hct541 driver between the PC and the Geckos.
If you ground the laptop
to the geckos the you are bypassing the isolation.
Jim
need. The circuit is completed inside the laptop.
I think the problem is the drive capability of a laptop may not be enough to
drive the
optoisolators. I us a 74hct541 driver between the PC and the Geckos.
If you ground the laptop
to the geckos the you are bypassing the isolation.
Jim
----- Original Message -----
From: "Weyland" <weyland@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Wednesday, September 17, 2003 12:51 AM
Subject: Re: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No
motion...
> On Wednesday 17 September 2003 01:11 am, Tim Goldstein spake:
>
> > Is the ground from the controller case power supply connected to the
> > laptop ground? If not you don't have a complete circuit and the motors
> > will never move.
>
> ... oh, you _*GOTTA*_ be kidding me... <sigh>
>
> I *COMPLETELY* misunderstood that +5V thing...
>
> So, you're saying that I should simply run a wire
> from chassis to the ground pin on the breakout board?
> Or does it need to go to one of the black
> wires from the molex connector breakout I made?
>
> I *may* just have to go back to the shop now to try this...
>
> It's 0200hrs here.
>
> Weyland
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
timg@...
> Moderator: pentam@... indigo_red@... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if
you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
sister site to the CCED group, as many of the same members are there, for OT
subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>
Discussion Thread
Weyland Smith
2003-09-16 21:38:38 UTC
Things to check? Crispy Fried Geckos? No motion...
Tim Goldstein
2003-09-16 22:11:53 UTC
RE: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
Weyland
2003-09-16 22:51:40 UTC
Re: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
Tim Goldstein
2003-09-16 23:07:26 UTC
RE: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
turbulatordude
2003-09-17 05:03:31 UTC
Re: Things to check? Crispy Fried Geckos? No motion...
James Cullins
2003-09-17 06:30:51 UTC
Re: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
James Cullins
2003-09-17 06:30:51 UTC
Re: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
Tim Goldstein
2003-09-17 07:53:25 UTC
RE: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
Jon Elson
2003-09-17 10:37:38 UTC
Re: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
Alan Marconett KM6VV
2003-09-17 10:39:02 UTC
Re: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
Alan Marconett KM6VV
2003-09-17 11:11:18 UTC
Re: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
Tim Goldstein
2003-09-17 12:08:59 UTC
RE: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
James Cullins
2003-09-17 12:32:37 UTC
Re: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
Weyland
2003-09-17 19:45:49 UTC
Thanks - was: Things to check? is now: RUNNING~!
Jon Elson
2003-09-17 22:31:38 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Tim Goldstein
2003-09-17 22:39:00 UTC
RE: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-18 06:46:45 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-18 06:59:02 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
turbulatordude
2003-09-18 07:51:25 UTC
Re: Thanks - was: Things to check? is now: RUNNING~!
Tim Goldstein
2003-09-18 08:09:15 UTC
RE: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-18 08:14:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Statman Designs, LLC
2003-09-18 08:26:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Jon Elson
2003-09-18 08:41:10 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
turbulatordude
2003-09-18 08:41:37 UTC
Re: Thanks - was: Things to check? is now: RUNNING~!
Jon Elson
2003-09-18 08:53:18 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Jon Elson
2003-09-18 08:54:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
turbulatordude
2003-09-18 09:15:51 UTC
Re: Thanks - was: Things to check? is now: - resoulution
sam sokolik
2003-09-18 10:28:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-19 20:57:49 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-19 21:01:46 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-19 21:04:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-19 21:11:09 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-19 21:16:16 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
JanRwl@A...
2003-09-19 21:19:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-19 21:21:03 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-19 21:25:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-19 21:34:05 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-19 21:36:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Antonius J.M. Groothuizen
2003-09-19 22:02:37 UTC
Re: Thanks - was: Things to check? is now: RUNNING~!
Tim Goldstein
2003-09-19 22:06:07 UTC
RE: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Tim Goldstein
2003-09-19 22:06:08 UTC
RE: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Tim Goldstein
2003-09-19 22:06:13 UTC
RE: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Tim Goldstein
2003-09-19 22:06:23 UTC
RE: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Jon Elson
2003-09-19 23:52:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
turbulatordude
2003-09-20 07:41:36 UTC
Re: Thanks - was: Things to check? back to basics - please
Weyland
2003-09-20 20:19:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-20 20:43:44 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-20 21:14:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Jon Elson
2003-09-21 09:26:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-22 09:31:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Jon Elson
2003-09-22 11:14:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-22 11:24:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Jon Elson
2003-09-22 20:46:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-22 22:07:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!