Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Posted by
Jon Elson
on 2003-09-19 23:52:09 UTC
Weyland wrote:
figure out how fast the pulses are coming out. First, you need to look
in the .ini file, and see what it says in the axis section, on the line that
reads INPUT_SCALE = nnnn. This is the number of steps per user
unit (inch or mm). I will assume it is set up for inches. Assume the
INPUT_SCALE = 2000. Now, when jogging at 25 IPM (as set in
the left-hand slider bar for the jog rate) and with the feed override
at 100 % (right hand slider bar) EMC will send 25 * 2000 pulses
per minute. that is 50,000 pulses per minute in this case. Divide by
60 and you get 833 pulses a second.
So, you can very easily tell what pulse rate EMC is putting out.
If you don't know how to read the ini file, here's how. I am assuming the
file is emc.ini, and that it is in the /usr/local/emc directory.
Open a terminal window.
type :
cd /usr/local/emc
to change the directory to the one you want to get the file from, and
then :
more emc.ini
To put the file, one page at a time, on the screen. Hit the space bar to
see the next page. hit the enter key to move down one line at a time in
the file. When you've seen enough, hit q to end it.
Jon
>On Thursday 18 September 2003 10:58 am, Statman Designs, LLC spake:OK, if you have EMC up and running, and can read the .ini file, you can
>
>
>
>>You could tell us how fast you are trying to run the motors.
>>
>>
>
>That's something I'm still trying to figure out.
>The electronics part of this is killing me...
>
>
figure out how fast the pulses are coming out. First, you need to look
in the .ini file, and see what it says in the axis section, on the line that
reads INPUT_SCALE = nnnn. This is the number of steps per user
unit (inch or mm). I will assume it is set up for inches. Assume the
INPUT_SCALE = 2000. Now, when jogging at 25 IPM (as set in
the left-hand slider bar for the jog rate) and with the feed override
at 100 % (right hand slider bar) EMC will send 25 * 2000 pulses
per minute. that is 50,000 pulses per minute in this case. Divide by
60 and you get 833 pulses a second.
So, you can very easily tell what pulse rate EMC is putting out.
If you don't know how to read the ini file, here's how. I am assuming the
file is emc.ini, and that it is in the /usr/local/emc directory.
Open a terminal window.
type :
cd /usr/local/emc
to change the directory to the one you want to get the file from, and
then :
more emc.ini
To put the file, one page at a time, on the screen. Hit the space bar to
see the next page. hit the enter key to move down one line at a time in
the file. When you've seen enough, hit q to end it.
Jon
Discussion Thread
Weyland Smith
2003-09-16 21:38:38 UTC
Things to check? Crispy Fried Geckos? No motion...
Tim Goldstein
2003-09-16 22:11:53 UTC
RE: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
Weyland
2003-09-16 22:51:40 UTC
Re: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
Tim Goldstein
2003-09-16 23:07:26 UTC
RE: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
turbulatordude
2003-09-17 05:03:31 UTC
Re: Things to check? Crispy Fried Geckos? No motion...
James Cullins
2003-09-17 06:30:51 UTC
Re: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
James Cullins
2003-09-17 06:30:51 UTC
Re: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
Tim Goldstein
2003-09-17 07:53:25 UTC
RE: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
Jon Elson
2003-09-17 10:37:38 UTC
Re: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
Alan Marconett KM6VV
2003-09-17 10:39:02 UTC
Re: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
Alan Marconett KM6VV
2003-09-17 11:11:18 UTC
Re: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
Tim Goldstein
2003-09-17 12:08:59 UTC
RE: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
James Cullins
2003-09-17 12:32:37 UTC
Re: [CAD_CAM_EDM_DRO] Things to check? Crispy Fried Geckos? No motion...
Weyland
2003-09-17 19:45:49 UTC
Thanks - was: Things to check? is now: RUNNING~!
Jon Elson
2003-09-17 22:31:38 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Tim Goldstein
2003-09-17 22:39:00 UTC
RE: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-18 06:46:45 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-18 06:59:02 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
turbulatordude
2003-09-18 07:51:25 UTC
Re: Thanks - was: Things to check? is now: RUNNING~!
Tim Goldstein
2003-09-18 08:09:15 UTC
RE: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-18 08:14:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Statman Designs, LLC
2003-09-18 08:26:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Jon Elson
2003-09-18 08:41:10 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
turbulatordude
2003-09-18 08:41:37 UTC
Re: Thanks - was: Things to check? is now: RUNNING~!
Jon Elson
2003-09-18 08:53:18 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Jon Elson
2003-09-18 08:54:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
turbulatordude
2003-09-18 09:15:51 UTC
Re: Thanks - was: Things to check? is now: - resoulution
sam sokolik
2003-09-18 10:28:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-19 20:57:49 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-19 21:01:46 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-19 21:04:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-19 21:11:09 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-19 21:16:16 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
JanRwl@A...
2003-09-19 21:19:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-19 21:21:03 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-19 21:25:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-19 21:34:05 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-19 21:36:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Antonius J.M. Groothuizen
2003-09-19 22:02:37 UTC
Re: Thanks - was: Things to check? is now: RUNNING~!
Tim Goldstein
2003-09-19 22:06:07 UTC
RE: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Tim Goldstein
2003-09-19 22:06:08 UTC
RE: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Tim Goldstein
2003-09-19 22:06:13 UTC
RE: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Tim Goldstein
2003-09-19 22:06:23 UTC
RE: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Jon Elson
2003-09-19 23:52:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
turbulatordude
2003-09-20 07:41:36 UTC
Re: Thanks - was: Things to check? back to basics - please
Weyland
2003-09-20 20:19:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-20 20:43:44 UTC
Re: [CAD_CAM_EDM_DRO] Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-20 21:14:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Jon Elson
2003-09-21 09:26:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-22 09:31:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Jon Elson
2003-09-22 11:14:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-22 11:24:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Jon Elson
2003-09-22 20:46:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!
Weyland
2003-09-22 22:07:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Thanks - was: Things to check? is now: RUNNING~!