Re: [CAD_CAM_EDM_DRO] Re: help
Posted by
Art Eckstein
on 2004-07-20 11:06:53 UTC
Alan,
Ver 3.x doesn't like 3 axis (x,y,z) in a G02/3. It will choke and give a
message to the effect that it will only take 2 axis.
Yes, the (dak) header requirement has been removed.
Yes, G02 /03 is in the form of G02 Xxx Yyy Iii Jjj Fff
I understand that in V4, you can use all three axis convention.
Art
At 12:29 PM 7/20/2004, you wrote:
OLDER THAN DIRT
Country Bubba
(Actually the inventor of Country and Bubba)
In God We Trust
axtein@...
LaGrange, GA
http://ns1.dicomm.net/~axtein/dro
[Non-text portions of this message have been removed]
Ver 3.x doesn't like 3 axis (x,y,z) in a G02/3. It will choke and give a
message to the effect that it will only take 2 axis.
Yes, the (dak) header requirement has been removed.
Yes, G02 /03 is in the form of G02 Xxx Yyy Iii Jjj Fff
I understand that in V4, you can use all three axis convention.
Art
At 12:29 PM 7/20/2004, you wrote:
>Hi Gary,Bubba
>
>Are you using an old vers. of TurboCNC? I thought the (dak) header
>requirement had been removed. ALSO, I'm wondering if the G03 block has
>BOTH J and K parameters. I seem to remember that it was required at one
>point. I'd even repeat the X, Y, Z's, even if they haven't changed.
>This may give you a clue.
>
>Alan KM6VV
>
>
>Gary Davison wrote:
>
> > Thanks Fred, but that did not work either. IT still cuts a crazy zig
> > zag pattern. Its as though Tcnc is ignoring the G03 code and cutting
> > a straight line instead.
> >
> > The doc's I have on Turbocnc state ( The "{dakcnc3.0}" header must be
> > present as the first line of the file). Also the file extendsion
> > is .cnc not .dnc. That's why I was using note pad.
> >
> > Sorry about the typo. Ring finger missing from left hand.....
> >
> > BTW, Anyone insterested I have posted links for the aluminum
> > extrusion I used on my CNC Router on my web page. Enjoy.
> >
> > Gary
> >
>
>
>
OLDER THAN DIRT
Country Bubba
(Actually the inventor of Country and Bubba)
In God We Trust
axtein@...
LaGrange, GA
http://ns1.dicomm.net/~axtein/dro
[Non-text portions of this message have been removed]
Discussion Thread
Ros
2000-03-25 21:40:26 UTC
help
riet91@y...
2001-08-09 02:26:28 UTC
help
mabw
2002-05-26 17:18:54 UTC
re:help
William Scalione
2003-03-15 11:27:15 UTC
Re: [CAD_CAM_EDM_DRO] help
Richard
2003-03-15 11:44:30 UTC
Re: help
Mariss Freimanis
2003-03-15 12:10:03 UTC
Re: help
frank_kandl
2003-09-10 07:34:42 UTC
help
Jon Elson
2003-09-10 09:41:53 UTC
Re: [CAD_CAM_EDM_DRO] help
Michael Milligan
2003-09-10 16:16:19 UTC
RE: [CAD_CAM_EDM_DRO] Dolphin CAD CAM Plus Mach2 Mill
Gary Davison
2004-07-19 18:58:56 UTC
help
Andy Wander
2004-07-19 19:20:50 UTC
RE: [CAD_CAM_EDM_DRO] help
Gary Davison
2004-07-19 19:33:49 UTC
Re: help
Fred Smith
2004-07-19 20:29:43 UTC
Re: help
Fred Smith
2004-07-19 20:47:12 UTC
Re: help
Gary Davison
2004-07-20 06:51:28 UTC
Re: help
Art Eckstein
2004-07-20 07:12:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: help
Gary Davison
2004-07-20 08:12:10 UTC
Re: help
Alan Marconett
2004-07-20 09:29:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: help
Art Eckstein
2004-07-20 11:06:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: help
Alan Marconett
2004-07-20 11:23:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: help
Gary Davison
2004-07-20 15:09:06 UTC
Re: help
Andy Wander
2004-07-20 15:28:22 UTC
RE: [CAD_CAM_EDM_DRO] Re: help