Re: [CAD_CAM_EDM_DRO] Re: help
Posted by
Alan Marconett
on 2004-07-20 11:23:12 UTC
Hi Art,
That's true, I only mention all three, in case the user was working in
another plane. Guess I should have mentioned I,J,K as well!
Helicals can be cut with G70, is that right? Then the "extra" axis
(such as Z) gets motion also.
Including All REQUIRED parms should do the trick in older vers. Getting
the latest vers is also recommended.
V4 sounds like it will be closer to standard practice.
Alan KM6VV
Art Eckstein wrote:
That's true, I only mention all three, in case the user was working in
another plane. Guess I should have mentioned I,J,K as well!
Helicals can be cut with G70, is that right? Then the "extra" axis
(such as Z) gets motion also.
Including All REQUIRED parms should do the trick in older vers. Getting
the latest vers is also recommended.
V4 sounds like it will be closer to standard practice.
Alan KM6VV
Art Eckstein wrote:
> Alan,
> Ver 3.x doesn't like 3 axis (x,y,z) in a G02/3. It will choke and give a
> message to the effect that it will only take 2 axis.
>
> Yes, the (dak) header requirement has been removed.
>
> Yes, G02 /03 is in the form of G02 Xxx Yyy Iii Jjj Fff
>
> I understand that in V4, you can use all three axis convention.
>
> Art
>
> At 12:29 PM 7/20/2004, you wrote:
>
>>Hi Gary,
>>
>>Are you using an old vers. of TurboCNC? I thought the (dak) header
>>requirement had been removed. ALSO, I'm wondering if the G03 block has
>>BOTH J and K parameters. I seem to remember that it was required at one
>>point. I'd even repeat the X, Y, Z's, even if they haven't changed.
>>This may give you a clue.
>>
>>Alan KM6VV
>>
>>
>>Gary Davison wrote:
>>
>>
>>>Thanks Fred, but that did not work either. IT still cuts a crazy zig
>>>zag pattern. Its as though Tcnc is ignoring the G03 code and cutting
>>>a straight line instead.
>>>
>>>The doc's I have on Turbocnc state ( The "{dakcnc3.0}" header must be
>>>present as the first line of the file). Also the file extendsion
>>>is .cnc not .dnc. That's why I was using note pad.
>>>
>>>Sorry about the typo. Ring finger missing from left hand.....
>>>
>>>BTW, Anyone insterested I have posted links for the aluminum
>>>extrusion I used on my CNC Router on my web page. Enjoy.
>>>
>>>Gary
>>>
>>
Discussion Thread
Ros
2000-03-25 21:40:26 UTC
help
riet91@y...
2001-08-09 02:26:28 UTC
help
mabw
2002-05-26 17:18:54 UTC
re:help
William Scalione
2003-03-15 11:27:15 UTC
Re: [CAD_CAM_EDM_DRO] help
Richard
2003-03-15 11:44:30 UTC
Re: help
Mariss Freimanis
2003-03-15 12:10:03 UTC
Re: help
frank_kandl
2003-09-10 07:34:42 UTC
help
Jon Elson
2003-09-10 09:41:53 UTC
Re: [CAD_CAM_EDM_DRO] help
Michael Milligan
2003-09-10 16:16:19 UTC
RE: [CAD_CAM_EDM_DRO] Dolphin CAD CAM Plus Mach2 Mill
Gary Davison
2004-07-19 18:58:56 UTC
help
Andy Wander
2004-07-19 19:20:50 UTC
RE: [CAD_CAM_EDM_DRO] help
Gary Davison
2004-07-19 19:33:49 UTC
Re: help
Fred Smith
2004-07-19 20:29:43 UTC
Re: help
Fred Smith
2004-07-19 20:47:12 UTC
Re: help
Gary Davison
2004-07-20 06:51:28 UTC
Re: help
Art Eckstein
2004-07-20 07:12:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: help
Gary Davison
2004-07-20 08:12:10 UTC
Re: help
Alan Marconett
2004-07-20 09:29:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: help
Art Eckstein
2004-07-20 11:06:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: help
Alan Marconett
2004-07-20 11:23:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: help
Gary Davison
2004-07-20 15:09:06 UTC
Re: help
Andy Wander
2004-07-20 15:28:22 UTC
RE: [CAD_CAM_EDM_DRO] Re: help