Re: [CAD_CAM_EDM_DRO] Gecko burned out
Posted by
Jon Elson
on 2004-10-17 09:50:55 UTC
Keith Clark wrote:
you should also check each winding for resistance, and compare to
the X motor. This still doesn't guarantee the motor is good, but it reduces
the probability that it is bad.
Did you actually find a loose wire? The loose wire doesn't need to short
to anything. Just being loose can permit sparking that can pop the
transistors
in the Gecko.
Jon
>I have been using Mach2 successfully with my bridgeport Boss 6 CNCWell, you should check your motors for shorts to ground. Probably
>retrofit until this morning when the y axis Gecko burned up. The
>machine had been off overnight and when I booted up and tried to
>move the axes off of home the drive immediately failed. It could be
>a loose wire that shorted, but I am concerned about just hooking up
>a new Gecko and having the same thing happen. This first move was a
>coordinated move of both x and y axis. There are no burned fuses
>that I can find and everything else seems to be functioning.
>
>
you should also check each winding for resistance, and compare to
the X motor. This still doesn't guarantee the motor is good, but it reduces
the probability that it is bad.
Did you actually find a loose wire? The loose wire doesn't need to short
to anything. Just being loose can permit sparking that can pop the
transistors
in the Gecko.
Jon
Discussion Thread
Keith Clark
2004-10-17 06:44:58 UTC
Gecko burned out
Jon Elson
2004-10-17 09:50:55 UTC
Re: [CAD_CAM_EDM_DRO] Gecko burned out
Keith Clark
2004-10-17 11:24:20 UTC
Re: Gecko burned out
Andrew Mawson
2004-10-17 12:31:54 UTC
Re: Gecko burned out
walid
2004-10-17 12:48:01 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Jon Elson
2004-10-17 15:15:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
JanRwl@A...
2004-10-17 16:42:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Andy Wander
2004-10-17 16:45:24 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out
turboking@j...
2004-10-17 18:27:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Keith Clark
2004-10-17 19:11:38 UTC
Re: Gecko burned out
R Rogers
2004-10-17 19:16:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
hotmail
2004-10-17 20:05:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
turbulatordude
2004-10-17 20:44:54 UTC
Re: Gecko burned out - loose wire
Jon Elson
2004-10-17 22:48:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
JanRwl@A...
2004-10-17 23:16:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Andy Wander
2004-10-18 04:35:31 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out
washcomp
2004-10-18 05:04:49 UTC
Re: Gecko burned out
R Rogers
2004-10-18 06:51:17 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Major A
2004-10-18 09:03:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Steve Stallings
2004-10-18 09:48:29 UTC
Re: Tinning wires - was Gecko burned out
John Dammeyer
2004-10-18 10:18:54 UTC
RE: Re: Gecko burned out
Andy Wander
2004-10-18 10:20:37 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Les Newell
2004-10-18 10:23:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
washcomp
2004-10-18 10:44:41 UTC
Re: Gecko burned out
Keith Clark
2004-10-18 11:06:24 UTC
Re: Gecko burned out
bank haam
2004-10-18 12:33:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
JanRwl@A...
2004-10-18 13:33:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
JanRwl@A...
2004-10-18 13:43:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
AbbyKatt
2004-10-18 13:45:04 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out
JanRwl@A...
2004-10-18 14:09:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Les Newell
2004-10-18 14:55:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Les Newell
2004-10-18 14:59:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Ron Kline
2004-10-18 16:02:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Keith Clark
2004-10-18 16:15:53 UTC
Re: Gecko burned out
Don Rogers
2004-10-18 16:15:58 UTC
Re: Gecko burned out
R Rogers
2004-10-18 16:37:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
caudlet
2004-10-18 17:33:52 UTC
Re: Gecko burned out (not about tinned leads)
Raymond Heckert
2004-10-18 18:04:00 UTC
Re: [CAD_CAM_EDM_DRO] Gecko burned out
Andy Wander
2004-10-18 18:07:38 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Andy Wander
2004-10-18 18:09:52 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out
washcomp
2004-10-18 18:28:03 UTC
Re: Gecko burned out (not about tinned leads)
Keith Clark
2004-10-18 18:50:33 UTC
Re: Gecko burned out
Keith Clark
2004-10-18 18:54:31 UTC
Re: Gecko burned out (not about tinned leads)
Keith Clark
2004-10-18 18:57:59 UTC
Re: Gecko burned out
Andy Wander
2004-10-18 19:05:45 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out
washcomp
2004-10-18 19:12:29 UTC
Re: Gecko burned out
Steve Stallings
2004-10-18 19:17:09 UTC
Re: Gecko burned out
Steve Stallings
2004-10-18 19:22:24 UTC
Re: Gecko burned out (not about tinned leads)
Keith Clark
2004-10-18 20:32:50 UTC
Re: Gecko burned out
ballendo
2004-10-18 21:37:16 UTC
Re: Gecko burned out
Dan Mauch
2004-10-19 07:38:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
caudlet
2004-10-19 08:59:49 UTC
Re: Gecko burned out (not about tinned leads)
Major A
2004-10-19 09:11:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out (not about tinned leads)
Dan Mauch
2004-10-19 09:35:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Steve Stallings
2004-10-19 09:50:09 UTC
Re: Gecko burned out (not about tinned leads)
Mariss Freimanis
2004-10-19 13:23:52 UTC
Re: Gecko burned out ( about tinned leads and other things)
jimkunzweiler
2004-10-19 13:42:27 UTC
What would you do? was Gecko burned out ( about tinned leads and other things)
metlmunchr
2004-10-19 14:18:35 UTC
Re: What would you do? was Gecko burned out ( about tinned leads and other thing
Alan Marconett
2004-10-19 14:36:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
caudlet
2004-10-19 16:02:15 UTC
Wow, was Gecko burned out ( about tinned leads and other things)
wanliker@a...
2004-10-28 21:13:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out