RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Posted by
R Rogers
on 2004-10-18 06:51:17 UTC
It's a common sense issue. If we tin the strands into a solid diameter then clamp the diameter between two flat surfaces the area of contact would be smaller than a bundle that can be flattened when clamped.
Ron
Andy Wander <awander@...> wrote:
Gotcha.
BTW, did you know that tinning stranded wires is NOT recommended for
wire-clamp-type terminals? The manufacturers specifically warn against it.
They say it will cause the connection to creep and loosen.
I still don't believe it by my "gut feeling", but I would guess they know
what they are talking about.
Andy Wander
Verrex Corporation
-----Original Message-----
From: JanRwl@... [mailto:JanRwl@...]
Sent: Monday, October 18, 2004 2:17 AM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
In a message dated 10/17/2004 6:47:15 PM Central Standard Time,
awander@... writes:
Are you saying that Geckos should have the safety circuitry built in, or
that the users should be more careful when they wire them up?
The latter.
The G204 will have features which I understand will make them (more)
idiot-proof, but they will COST more. Understandable. I think I
understand that
the G201 and G210 will still be available for the old pricing. If so,
good.
I read instructions, tin stranded wire-ends, tighten screw-terminations
properly, use correct DC supplies, regulated or not, and find that a much
more
satisfyingly economical approach than being sloppy and having to purchase
replacements every few days.
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Yahoo! Groups Links
---------------------------------
Do you Yahoo!?
Read only the mail you want - Yahoo! Mail SpamGuard.
[Non-text portions of this message have been removed]
Ron
Andy Wander <awander@...> wrote:
Gotcha.
BTW, did you know that tinning stranded wires is NOT recommended for
wire-clamp-type terminals? The manufacturers specifically warn against it.
They say it will cause the connection to creep and loosen.
I still don't believe it by my "gut feeling", but I would guess they know
what they are talking about.
Andy Wander
Verrex Corporation
-----Original Message-----
From: JanRwl@... [mailto:JanRwl@...]
Sent: Monday, October 18, 2004 2:17 AM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
In a message dated 10/17/2004 6:47:15 PM Central Standard Time,
awander@... writes:
Are you saying that Geckos should have the safety circuitry built in, or
that the users should be more careful when they wire them up?
The latter.
The G204 will have features which I understand will make them (more)
idiot-proof, but they will COST more. Understandable. I think I
understand that
the G201 and G210 will still be available for the old pricing. If so,
good.
I read instructions, tin stranded wire-ends, tighten screw-terminations
properly, use correct DC supplies, regulated or not, and find that a much
more
satisfyingly economical approach than being sloppy and having to purchase
replacements every few days.
Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
http://www.metalworking.com/news_servers.html
http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.
NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner
Yahoo! Groups Links
---------------------------------
Do you Yahoo!?
Read only the mail you want - Yahoo! Mail SpamGuard.
[Non-text portions of this message have been removed]
Discussion Thread
Keith Clark
2004-10-17 06:44:58 UTC
Gecko burned out
Jon Elson
2004-10-17 09:50:55 UTC
Re: [CAD_CAM_EDM_DRO] Gecko burned out
Keith Clark
2004-10-17 11:24:20 UTC
Re: Gecko burned out
Andrew Mawson
2004-10-17 12:31:54 UTC
Re: Gecko burned out
walid
2004-10-17 12:48:01 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Jon Elson
2004-10-17 15:15:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
JanRwl@A...
2004-10-17 16:42:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Andy Wander
2004-10-17 16:45:24 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out
turboking@j...
2004-10-17 18:27:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Keith Clark
2004-10-17 19:11:38 UTC
Re: Gecko burned out
R Rogers
2004-10-17 19:16:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
hotmail
2004-10-17 20:05:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
turbulatordude
2004-10-17 20:44:54 UTC
Re: Gecko burned out - loose wire
Jon Elson
2004-10-17 22:48:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
JanRwl@A...
2004-10-17 23:16:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Andy Wander
2004-10-18 04:35:31 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out
washcomp
2004-10-18 05:04:49 UTC
Re: Gecko burned out
R Rogers
2004-10-18 06:51:17 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Major A
2004-10-18 09:03:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Steve Stallings
2004-10-18 09:48:29 UTC
Re: Tinning wires - was Gecko burned out
John Dammeyer
2004-10-18 10:18:54 UTC
RE: Re: Gecko burned out
Andy Wander
2004-10-18 10:20:37 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Les Newell
2004-10-18 10:23:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
washcomp
2004-10-18 10:44:41 UTC
Re: Gecko burned out
Keith Clark
2004-10-18 11:06:24 UTC
Re: Gecko burned out
bank haam
2004-10-18 12:33:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
JanRwl@A...
2004-10-18 13:33:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
JanRwl@A...
2004-10-18 13:43:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
AbbyKatt
2004-10-18 13:45:04 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out
JanRwl@A...
2004-10-18 14:09:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Les Newell
2004-10-18 14:55:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Les Newell
2004-10-18 14:59:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Ron Kline
2004-10-18 16:02:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Keith Clark
2004-10-18 16:15:53 UTC
Re: Gecko burned out
Don Rogers
2004-10-18 16:15:58 UTC
Re: Gecko burned out
R Rogers
2004-10-18 16:37:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
caudlet
2004-10-18 17:33:52 UTC
Re: Gecko burned out (not about tinned leads)
Raymond Heckert
2004-10-18 18:04:00 UTC
Re: [CAD_CAM_EDM_DRO] Gecko burned out
Andy Wander
2004-10-18 18:07:38 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Andy Wander
2004-10-18 18:09:52 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out
washcomp
2004-10-18 18:28:03 UTC
Re: Gecko burned out (not about tinned leads)
Keith Clark
2004-10-18 18:50:33 UTC
Re: Gecko burned out
Keith Clark
2004-10-18 18:54:31 UTC
Re: Gecko burned out (not about tinned leads)
Keith Clark
2004-10-18 18:57:59 UTC
Re: Gecko burned out
Andy Wander
2004-10-18 19:05:45 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out
washcomp
2004-10-18 19:12:29 UTC
Re: Gecko burned out
Steve Stallings
2004-10-18 19:17:09 UTC
Re: Gecko burned out
Steve Stallings
2004-10-18 19:22:24 UTC
Re: Gecko burned out (not about tinned leads)
Keith Clark
2004-10-18 20:32:50 UTC
Re: Gecko burned out
ballendo
2004-10-18 21:37:16 UTC
Re: Gecko burned out
Dan Mauch
2004-10-19 07:38:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
caudlet
2004-10-19 08:59:49 UTC
Re: Gecko burned out (not about tinned leads)
Major A
2004-10-19 09:11:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out (not about tinned leads)
Dan Mauch
2004-10-19 09:35:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
Steve Stallings
2004-10-19 09:50:09 UTC
Re: Gecko burned out (not about tinned leads)
Mariss Freimanis
2004-10-19 13:23:52 UTC
Re: Gecko burned out ( about tinned leads and other things)
jimkunzweiler
2004-10-19 13:42:27 UTC
What would you do? was Gecko burned out ( about tinned leads and other things)
metlmunchr
2004-10-19 14:18:35 UTC
Re: What would you do? was Gecko burned out ( about tinned leads and other thing
Alan Marconett
2004-10-19 14:36:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out
caudlet
2004-10-19 16:02:15 UTC
Wow, was Gecko burned out ( about tinned leads and other things)
wanliker@a...
2004-10-28 21:13:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out