CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out

Posted by Dan Mauch
on 2004-10-19 07:38:17 UTC
I just tried inserting a piece of 18 awg stranded wire into a Gecko terminal
block and it went in with no problem. It wasn't even tight. I also inserted
the leads for a 470 UF cap. to see if it would work on terminals 1 and 2 .
So either the screws weren't backed off far enough or he has 14 AWG wire.
Dan
----- Original Message -----
From: "Andy Wander" <awander@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Monday, October 18, 2004 7:04 PM
Subject: RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out


>
> I would bet that you can get the 16AWG in if you first open the screw all
> the way, and then push a round awl in to open up the tab.
>
> Even if you can't , though, for 7Amps, unless the runs are really long,
> 18AWG would probably do it.
>
> Andy Wander
> Verrex Corporation
>
>

Discussion Thread

Keith Clark 2004-10-17 06:44:58 UTC Gecko burned out Jon Elson 2004-10-17 09:50:55 UTC Re: [CAD_CAM_EDM_DRO] Gecko burned out Keith Clark 2004-10-17 11:24:20 UTC Re: Gecko burned out Andrew Mawson 2004-10-17 12:31:54 UTC Re: Gecko burned out walid 2004-10-17 12:48:01 UTC RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out Jon Elson 2004-10-17 15:15:23 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out JanRwl@A... 2004-10-17 16:42:23 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out Andy Wander 2004-10-17 16:45:24 UTC RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out turboking@j... 2004-10-17 18:27:13 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out Keith Clark 2004-10-17 19:11:38 UTC Re: Gecko burned out R Rogers 2004-10-17 19:16:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out hotmail 2004-10-17 20:05:08 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out turbulatordude 2004-10-17 20:44:54 UTC Re: Gecko burned out - loose wire Jon Elson 2004-10-17 22:48:08 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out JanRwl@A... 2004-10-17 23:16:46 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out Andy Wander 2004-10-18 04:35:31 UTC RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out washcomp 2004-10-18 05:04:49 UTC Re: Gecko burned out R Rogers 2004-10-18 06:51:17 UTC RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out Major A 2004-10-18 09:03:30 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out Steve Stallings 2004-10-18 09:48:29 UTC Re: Tinning wires - was Gecko burned out John Dammeyer 2004-10-18 10:18:54 UTC RE: Re: Gecko burned out Andy Wander 2004-10-18 10:20:37 UTC RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out Les Newell 2004-10-18 10:23:52 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out washcomp 2004-10-18 10:44:41 UTC Re: Gecko burned out Keith Clark 2004-10-18 11:06:24 UTC Re: Gecko burned out bank haam 2004-10-18 12:33:01 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out JanRwl@A... 2004-10-18 13:33:22 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out JanRwl@A... 2004-10-18 13:43:23 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out AbbyKatt 2004-10-18 13:45:04 UTC RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out JanRwl@A... 2004-10-18 14:09:43 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out Les Newell 2004-10-18 14:55:51 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out Les Newell 2004-10-18 14:59:23 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out Ron Kline 2004-10-18 16:02:02 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out Keith Clark 2004-10-18 16:15:53 UTC Re: Gecko burned out Don Rogers 2004-10-18 16:15:58 UTC Re: Gecko burned out R Rogers 2004-10-18 16:37:27 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out caudlet 2004-10-18 17:33:52 UTC Re: Gecko burned out (not about tinned leads) Raymond Heckert 2004-10-18 18:04:00 UTC Re: [CAD_CAM_EDM_DRO] Gecko burned out Andy Wander 2004-10-18 18:07:38 UTC RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out Andy Wander 2004-10-18 18:09:52 UTC RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out washcomp 2004-10-18 18:28:03 UTC Re: Gecko burned out (not about tinned leads) Keith Clark 2004-10-18 18:50:33 UTC Re: Gecko burned out Keith Clark 2004-10-18 18:54:31 UTC Re: Gecko burned out (not about tinned leads) Keith Clark 2004-10-18 18:57:59 UTC Re: Gecko burned out Andy Wander 2004-10-18 19:05:45 UTC RE: [CAD_CAM_EDM_DRO] Re: Gecko burned out washcomp 2004-10-18 19:12:29 UTC Re: Gecko burned out Steve Stallings 2004-10-18 19:17:09 UTC Re: Gecko burned out Steve Stallings 2004-10-18 19:22:24 UTC Re: Gecko burned out (not about tinned leads) Keith Clark 2004-10-18 20:32:50 UTC Re: Gecko burned out ballendo 2004-10-18 21:37:16 UTC Re: Gecko burned out Dan Mauch 2004-10-19 07:38:17 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out caudlet 2004-10-19 08:59:49 UTC Re: Gecko burned out (not about tinned leads) Major A 2004-10-19 09:11:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out (not about tinned leads) Dan Mauch 2004-10-19 09:35:22 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out Steve Stallings 2004-10-19 09:50:09 UTC Re: Gecko burned out (not about tinned leads) Mariss Freimanis 2004-10-19 13:23:52 UTC Re: Gecko burned out ( about tinned leads and other things) jimkunzweiler 2004-10-19 13:42:27 UTC What would you do? was Gecko burned out ( about tinned leads and other things) metlmunchr 2004-10-19 14:18:35 UTC Re: What would you do? was Gecko burned out ( about tinned leads and other thing Alan Marconett 2004-10-19 14:36:27 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out caudlet 2004-10-19 16:02:15 UTC Wow, was Gecko burned out ( about tinned leads and other things) wanliker@a... 2004-10-28 21:13:48 UTC Re: [CAD_CAM_EDM_DRO] Re: Gecko burned out