Re: [CAD_CAM_EDM_DRO] Re: plasma accuracy
Posted by
Randy Wilson
on 2004-12-21 05:42:05 UTC
Why not just use a commercial dryer?
See: <http://www.pulsar-superdry.com/> for an example.
Google returns 68,700 hits on the term "compressed air dryer"
See: <http://www.pulsar-superdry.com/> for an example.
Google returns 68,700 hits on the term "compressed air dryer"
On Dec 21, 2004, at 2:26 AM, turbulatordude wrote:
>
>
> --- In CAD_CAM_EDM_DRO@yahoogroups.com, R Rogers <rogersmach@y...>
> wrote:
>> Oh ok, well that makes sense. moisture in the air being conductive.
> Could one use an inert gas such as Co2 with better results than air
> regarding tip failure? Argon would be better probably but much more
> expensive.
>>
>> Ron
>
> I'm not sure of the air volume, but you can solve the compressed air
> moisture pretty easily. Albeit with some work.
>
> A post compressor heat exchanger would help drop the compressed air
> temperature somewhat.
>
> A simple refrigerator with airline coiled inside would offer a
> mechanical cooling of the air line.
>
> The exit air of the refrigerator could then be used as the pre-
> cooling side of the heat exchanger. Warming the air to the torch,
> but using some of the colder refrigerated air to pre-cool the air
> entering the refrigerator. This would reduce the load on the
> refrigerator.
>
> Putting a bucket of water in the frige and the coil in tht would add
> a signifigant thermal mass also.
>
> Just some ideas.
>
> Dave
>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
> timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
> [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach
> it if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be
> a sister site to the CCED group, as many of the same members are
> there, for OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING
> THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
>
>
Discussion Thread
sargossa_99
2004-12-17 06:58:00 UTC
plasma accuracy
turbulatordude
2004-12-17 11:19:50 UTC
Re: plasma accuracy
Graham Stabler
2004-12-17 13:35:47 UTC
Re: plasma accuracy
V FONG
2004-12-17 14:33:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: plasma accuracy
turbulatordude
2004-12-17 15:22:18 UTC
Re: plasma accuracy
Graham Stabler
2004-12-17 15:50:52 UTC
Re: plasma accuracy
John Heritage
2004-12-18 07:30:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: plasma accuracy
Graham Stabler
2004-12-18 08:35:04 UTC
Re: plasma accuracy
caudlet
2004-12-18 08:35:55 UTC
Re: plasma accuracy
Graham Stabler
2004-12-18 09:12:58 UTC
Re: plasma accuracy
R Rogers
2004-12-18 09:38:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: plasma accuracy
turbulatordude
2004-12-18 10:46:15 UTC
Re: plasma accuracy
caudlet
2004-12-18 13:55:31 UTC
Re: plasma accuracy
metlmunchr
2004-12-18 15:14:59 UTC
Re: plasma accuracy
Hal Eckhart
2004-12-18 15:42:28 UTC
gecko 201/210 opinions
Raymond Heckert
2004-12-18 17:24:32 UTC
Re: [CAD_CAM_EDM_DRO] plasma accuracy
Raymond Heckert
2004-12-18 17:24:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: plasma accuracy
caudlet
2004-12-18 17:39:34 UTC
Re: gecko 201/210 opinions
Hal Eckhart
2004-12-18 18:31:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: gecko 201/210 opinions
Hal Eckhart
2004-12-18 18:53:42 UTC
Re: [CAD_CAM_EDM_DRO] plasma accuracy
Jon Elson
2004-12-18 20:40:43 UTC
Re: [CAD_CAM_EDM_DRO] gecko 201/210 opinions
turbulatordude
2004-12-18 21:40:12 UTC
Re: plasma accuracy
Randy Brown
2004-12-19 08:03:26 UTC
RE: [CAD_CAM_EDM_DRO] Re: plasma accuracy
caudlet
2004-12-19 13:12:59 UTC
Re: gecko 201/210 opinions
m0nkey0ne
2004-12-20 16:22:25 UTC
Re: plasma accuracy
R Rogers
2004-12-20 17:40:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: plasma accuracy
turbulatordude
2004-12-20 23:26:48 UTC
Re: plasma accuracy
Randy Wilson
2004-12-21 05:42:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: plasma accuracy
Bruce Pigeon
2004-12-21 09:40:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: plasma accuracy
turbulatordude
2004-12-21 09:46:24 UTC
Re: plasma accuracy