Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish
Posted by
cnc002@a...
on 2005-12-22 10:36:40 UTC
In a message dated 12/22/2005 12:49:26 P.M. Eastern Standard Time,
ronbiblio@... writes:
Hi:
We have an Amish neighbor who runs a machine tool shop.
He is seeking some sort of stand alone motion controller that could be
programed using G Code (via a word processor in ASCII).
Does anybody have any suggestions or ideas?
Thanks, Ron
Kinzers, PA 17535
Internet: RareBooks@...
Ron:
Try a Fagor 8000 series control. You can use a simple ASCII editor such as
DOS editor, Notepad, the old PCWrite as long as you know the control codes to
place at the beginning and the end of the program file. Most of the time a
bunch of NUL characters will work at the beginning and the end.
This used to be the General Electric Control in the 80s they were called
Mark Century controls but they were manufactured by a company in Spain for them.
Fagor has been the importer and distributor since GE dropped the line and
hooked up with Fanuc.
The controls are not cheap but also not expensive, as proprietary
controllers go, and as I recall even the lowest priced one can control up to 4 axis.
Here is a link, if it doesn't work just copy and paste it into your web
address bar:
_Fagor Products_ (http://www.fagor-automation.com/Products/Products.htm)
I hope this helps,
Randy Abernathy
[Non-text portions of this message have been removed]
ronbiblio@... writes:
Hi:
We have an Amish neighbor who runs a machine tool shop.
He is seeking some sort of stand alone motion controller that could be
programed using G Code (via a word processor in ASCII).
Does anybody have any suggestions or ideas?
Thanks, Ron
Kinzers, PA 17535
Internet: RareBooks@...
Ron:
Try a Fagor 8000 series control. You can use a simple ASCII editor such as
DOS editor, Notepad, the old PCWrite as long as you know the control codes to
place at the beginning and the end of the program file. Most of the time a
bunch of NUL characters will work at the beginning and the end.
This used to be the General Electric Control in the 80s they were called
Mark Century controls but they were manufactured by a company in Spain for them.
Fagor has been the importer and distributor since GE dropped the line and
hooked up with Fanuc.
The controls are not cheap but also not expensive, as proprietary
controllers go, and as I recall even the lowest priced one can control up to 4 axis.
Here is a link, if it doesn't work just copy and paste it into your web
address bar:
_Fagor Products_ (http://www.fagor-automation.com/Products/Products.htm)
I hope this helps,
Randy Abernathy
[Non-text portions of this message have been removed]
Discussion Thread
ronbiblio
2005-12-22 09:48:10 UTC
CNC Without a PC for Amish
Jeff Goldberg
2005-12-22 09:59:07 UTC
RE: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish
STAN MCDONALD
2005-12-22 10:02:12 UTC
Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish
JanRwl@A...
2005-12-22 10:06:27 UTC
Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish
Dhiren Shah
2005-12-22 10:14:31 UTC
RE: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish
cnc002@a...
2005-12-22 10:36:40 UTC
Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish
Alan Marconett
2005-12-22 10:37:35 UTC
RE: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish
Codesuidae
2005-12-22 10:46:24 UTC
Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish
Ken Strauss
2005-12-22 11:02:22 UTC
RE: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish
Jon Elson
2005-12-22 18:50:17 UTC
Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish
Jeffrey Goldberg
2005-12-22 19:49:50 UTC
RE: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish
Jon Elson
2005-12-22 21:43:10 UTC
Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish
BobWarfield
2005-12-22 23:40:04 UTC
Re: CNC Without a PC for Amish
Peter Reilley
2005-12-23 04:51:03 UTC
Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish
Richard L. Wurdack
2005-12-23 05:10:21 UTC
Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish
Alan Marconett
2005-12-23 09:08:08 UTC
RE: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish
Jon Elson
2005-12-23 09:51:02 UTC
Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish
Peter Reilley
2005-12-23 12:37:19 UTC
Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish
Peter Reilley
2005-12-23 12:43:34 UTC
Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish
Raymond Heckert
2005-12-23 17:08:37 UTC
Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish
Raymond Heckert
2005-12-23 17:14:50 UTC
Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish
Jim Peck
2005-12-24 06:47:18 UTC
Amish CNC Operators