CAD CAM EDM DRO - Yahoo Group Archive

RE: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish

on 2005-12-22 10:37:35 UTC
HI list,

Sounds like it's time to dig out the old ASR-33 teletype! Or was it KSR? I
can never remember. OK, the one with the tape reader/punch.

Your "edit" by typing a block. If you make a mistake, you "rub out" with
all holes (7Fh or FFh) and type the block again!

Alan KM6VV

> If he does not want to use a PC, how does he plan to use a word processor
> to
> write his G codes? I suppose a CNC controller offers a word processor!
>
> Dhiren Shah, Dir., Operations
> -----Original Message-----
> Hi:
>
> We have an Amish neighbor who runs a machine tool shop.
>
> He is seeking some sort of stand alone motion controller that could be
> programed using G Code (via a word processor in ASCII).
>
> Does anybody have any suggestions or ideas?
>
> Thanks, Ron
>
> Kinzers, PA 17535

Discussion Thread

ronbiblio 2005-12-22 09:48:10 UTC CNC Without a PC for Amish Jeff Goldberg 2005-12-22 09:59:07 UTC RE: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish STAN MCDONALD 2005-12-22 10:02:12 UTC Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish JanRwl@A... 2005-12-22 10:06:27 UTC Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish Dhiren Shah 2005-12-22 10:14:31 UTC RE: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish cnc002@a... 2005-12-22 10:36:40 UTC Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish Alan Marconett 2005-12-22 10:37:35 UTC RE: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish Codesuidae 2005-12-22 10:46:24 UTC Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish Ken Strauss 2005-12-22 11:02:22 UTC RE: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish Jon Elson 2005-12-22 18:50:17 UTC Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish Jeffrey Goldberg 2005-12-22 19:49:50 UTC RE: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish Jon Elson 2005-12-22 21:43:10 UTC Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish BobWarfield 2005-12-22 23:40:04 UTC Re: CNC Without a PC for Amish Peter Reilley 2005-12-23 04:51:03 UTC Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish Richard L. Wurdack 2005-12-23 05:10:21 UTC Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish Alan Marconett 2005-12-23 09:08:08 UTC RE: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish Jon Elson 2005-12-23 09:51:02 UTC Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish Peter Reilley 2005-12-23 12:37:19 UTC Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish Peter Reilley 2005-12-23 12:43:34 UTC Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish Raymond Heckert 2005-12-23 17:08:37 UTC Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish Raymond Heckert 2005-12-23 17:14:50 UTC Re: [CAD_CAM_EDM_DRO] CNC Without a PC for Amish Jim Peck 2005-12-24 06:47:18 UTC Amish CNC Operators