Re: SLA7062 technical stuff - supply voltages
Posted by
turbulatordude
on 2006-05-08 14:51:32 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "turyga1963" <TIntruder@...>
wrote:
transformers.
a 24V transformer times 1.414 to get 34 volts fits well to a 44 volt
maximum unit.
48 volts to the Gecko offers about 66 volts to the drive. Again a
nice fit without leaving too much room for improvement.
Some time ago, Mariss posted some results of life expectancy of his
drives. at 114 volts the life expectancy was something in the minutes
range. at 80 volts it was in the years, at 90 it was in the months
and only got worse as the voltage increased.
I suspect that this is the case with all drives. there is a sweet
spot that offers a very long life and a bleeding edge where one
mistake, one time results in that sinking feeling you get when you
smell that magic smoke.
Dave
wrote:
>I found that many of the parts seem to fit well with existing
> Dave,
>
> Good to know. Problem in my case and I suspect that of many others
> who have had similar problems is that we were expressly told by HCNC
> that we could use up to 42vdc and the circuit board is even
> silkscreened to show that voltage. Further we were told the closer
> to 42vdc we got, the better as that would insure maximum power/speed
> from the steppers.
>
> Oh well, live and learn...
>
> Tom
transformers.
a 24V transformer times 1.414 to get 34 volts fits well to a 44 volt
maximum unit.
48 volts to the Gecko offers about 66 volts to the drive. Again a
nice fit without leaving too much room for improvement.
Some time ago, Mariss posted some results of life expectancy of his
drives. at 114 volts the life expectancy was something in the minutes
range. at 80 volts it was in the years, at 90 it was in the months
and only got worse as the voltage increased.
I suspect that this is the case with all drives. there is a sweet
spot that offers a very long life and a bleeding edge where one
mistake, one time results in that sinking feeling you get when you
smell that magic smoke.
Dave
Discussion Thread
Phil Mattison
2006-05-06 10:54:19 UTC
New Article Posted
lcdpublishing
2006-05-06 14:04:40 UTC
Re: New Article Posted
Dave Rigotti
2006-05-06 15:12:13 UTC
Re: New Article Posted
Phil Mattison
2006-05-06 15:16:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: New Article Posted
turbulatordude
2006-05-06 15:55:53 UTC
Re: New Article Posted
Dave Rigotti
2006-05-06 17:29:17 UTC
Re: New Article Posted
wanliker@a...
2006-05-06 18:50:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: New Article Posted
ballendo
2006-05-06 20:08:11 UTC
Re: New Article Posted
ballendo
2006-05-06 20:33:19 UTC
missed steps going into sync mode? Re: New Article Posted
ballendo
2006-05-07 01:04:56 UTC
Re: New Article Posted
Dave Rigotti
2006-05-07 04:42:40 UTC
Re: New Article Posted
Phil Mattison
2006-05-07 10:01:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: New Article Posted
Phil Mattison
2006-05-07 10:28:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: New Article Posted
Phil Mattison
2006-05-07 10:34:48 UTC
Re: [CAD_CAM_EDM_DRO] missed steps going into sync mode? Re: New Article Posted
ballendo
2006-05-07 18:03:59 UTC
Re: New Article Posted
ballendo
2006-05-07 18:15:42 UTC
Re: New Article Posted
Phil Mattison
2006-05-07 18:41:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: New Article Posted
turyga1963
2006-05-07 21:55:42 UTC
Re: New Article Posted
turbulatordude
2006-05-07 21:57:23 UTC
Re: New Article Posted
wanliker@a...
2006-05-07 22:07:37 UTC
New Article Posted
turyga1963
2006-05-08 00:25:30 UTC
Re: New Article Posted
ballendo
2006-05-08 03:25:17 UTC
Re: New Article Posted
Alan Marconett
2006-05-08 08:31:35 UTC
RE: [CAD_CAM_EDM_DRO] Re: New Article Posted
jeffalanp
2006-05-08 08:34:47 UTC
SLA7062 and Re: New Article Posted
turbulatordude
2006-05-08 08:40:12 UTC
Re: New Article Posted
Codesuidae
2006-05-08 08:50:26 UTC
Re: [CAD_CAM_EDM_DRO] SLA7062 and Re: New Article Posted
Codesuidae
2006-05-08 09:08:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: New Article Posted
turbulatordude
2006-05-08 09:15:26 UTC
SLA7062 technical stuff
wanliker@a...
2006-05-08 10:04:12 UTC
New Article Posted
cncnovice
2006-05-08 11:04:30 UTC
Re: New Article Posted
wanliker@a...
2006-05-08 11:16:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: New Article Posted
cncnovice
2006-05-08 11:37:54 UTC
Re: New Article Posted
Codesuidae
2006-05-08 12:57:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: New Article Posted
turyga1963
2006-05-08 14:13:40 UTC
SLA7062 and Re: New Article Posted
turyga1963
2006-05-08 14:22:17 UTC
Re: SLA7062 technical stuff
turyga1963
2006-05-08 14:23:54 UTC
SLA7062 and Re: New Article Posted
turbulatordude
2006-05-08 14:43:26 UTC
Re: New Article Posted - Moderators warning
turbulatordude
2006-05-08 14:51:32 UTC
Re: SLA7062 technical stuff - supply voltages
turyga1963
2006-05-08 15:01:10 UTC
Re: New Article Posted
turyga1963
2006-05-08 15:16:18 UTC
Re: New Article Posted
turyga1963
2006-05-08 15:21:01 UTC
Re: SLA7062 technical stuff - supply voltages
John Dammeyer
2006-05-08 15:29:03 UTC
RE: [CAD_CAM_EDM_DRO] Re: SLA7062 technical stuff - supply voltages
Paul Kelly
2006-05-08 15:32:39 UTC
RE: [CAD_CAM_EDM_DRO] Re: SLA7062 technical stuff - supply voltages
R Rogers
2006-05-08 16:07:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: SLA7062 technical stuff
turbulatordude
2006-05-08 18:43:15 UTC
Re: SLA7062 technical stuff - supply voltages
ballendo
2006-05-08 19:48:42 UTC
SLA7062 and Re: New Article Posted
ballendo
2006-05-08 20:21:07 UTC
Sync mode musings was Re: New Article Posted
jeffalanp
2006-05-08 20:28:56 UTC
SLA7062 and Re: New Article Posted
ballendo
2006-05-08 22:38:17 UTC
OT SLA7062 and Re: New Article Posted
Lester Caine
2006-05-08 23:14:12 UTC
Re: [CAD_CAM_EDM_DRO] SLA7062 and Re: New Article Posted
wanliker@a...
2006-05-08 23:24:59 UTC
Re: [CAD_CAM_EDM_DRO] SLA7062 and Re: New Article Posted
Mariss Freimanis
2006-05-09 10:11:39 UTC
Re: SLA7062 technical stuff - supply voltages
turyga1963
2006-05-10 22:50:16 UTC
Re: SLA7062 technical stuff - supply voltages
Mariss Freimanis
2006-05-11 06:36:52 UTC
Re: SLA7062 technical stuff - supply voltages
Alan Rothenbush
2006-06-12 12:21:45 UTC
Re: SLA7062 technical stuff - supply voltages